This is a linker option, so provided it's added to LDFLAGS then it can be
dropped from CFLAGS without changing the compiler behaviour.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
These classes are based on the Quadrature Encoder blocks of the i.MXRT
MCUs. The i.MXRT 102x has two encoders, the other ones four. The i.MXRT
101x does not support this function. It is implemented as two classes,
Encoder and Counter.
The number of pins that can be uses as inputs is limited by the MCU
architecture and the board schematics. The Encoder class supports:
- Defining the module.
- Defining the input pins.
- Defining a pin for an index signal.
- Defining a pin for a reset signal.
- Defining an output pin showing the compare match signal.
- Setting the number of cycles per revolution (min/max).
- Setting the initial value for the position.
- Setting the counting direction.
- Setting a glitch filter.
- Defining callbacks for getting to a specific position, overrun and
underrun (starting the next revolution). These callbacks can be hard
interrupts to ensure short latency.
The encoder counts all phases of a cycle. The span for the position is
2**32, for the revolution is 2**16. The highest input frequency is
CPU-Clock/24. Note that the "phases" argument is emulated at the API
level (the hardware will always count all phases).
The Counter mode counts single pulses on input A of the Encoder. The
configuration supports:
- Defining the module.
- Defining the input pin.
- Defining the counting direction, either fixed or controlled by the level
of an input pin.
- Defining a pin for an index signal.
- Defining an output pin showing the compare match signal.
- Setting the counter value.
- Setting the glitch filter.
- Defining a callback which is called at a certain value.
- Settings for MIMXRT1015. The MIMXRT1015 MCU has only one encoder/counter
unit.
The counting range is 0 - 2**32-1 and a 16 bit overrun counter. The
highest input frequency is CPU-Clock/12.
The implementation of the `.irq()` method uses the common code from
`shared/runtime/mpirq.c`, including the `irq().flags()` and
`irq().trigger()` methods.
Signed-off-by: robert-hh <robert@hammelrath.com>
With this change, can simply add `LD_FILES` to a board's `mpconfigboard.mk`
to change the linker scripts, such as to change the section sizes, or
change the contents for each region. Example usage:
LD_FILES = $(BOARD_DIR)/my_board.ld boards/common.ld
Signed-off-by: Dryw Wade <dryw.wade@sparkfun.com>
MicroPython needs to handle the UART idle interrupt, which is not something
that the standard SDK provides. This was previously fixed by including in
the mimxrt port a modified copy of `fsl_lpuart.c`.
This commit changes how that's done by building the unmodified
`fsl_lpuart.c` directly from the SDK, and using linker wrapping to override
the necessary functions to get at the idle IRQ. As part of this, the code
is updated to work with the latest SDK.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
This allows user C modules to be built into the mimxrt port. The change is
copied from `samd/Makefile`.
Fixes issue #18292.
Signed-off-by: Dryw Wade <dryw.wade@sparkfun.com>
This commit adds PSRAM support for Teensy 4.1 and other mimxrt boards.
It's enabled by default for Teensy 4.1.
This implementation is based on the Teensy Arduino core PSRAM code, and
Paul Stoffregen has agreed for it to be published here under the MIT
license, see https://github.com/micropython/micropython/pull/18288#issuecomment-3806784632
This addresses issue #18281.
Signed-off-by: Dryw Wade <dryw.wade@sparkfun.com>
The default size for the ROM partition is 256k, and it is placed in flash
between the text and writable vfs sections. Its size can be changed in
`mpconfigboard.mk` by defining `MICROPY_HW_ROMFS_BYTES` to a different
value, but it must not be smaller than a single sector.
The MIMXRT1170_EVK and SEEED ARCH MIX ROMFS boards use a larger size of
512kB. ROMFS support is disabled for MIMXRT1050_EVKB due to issues with
Hyperflash.
The extents of the ROM partition are defined by the linker-level symbols
`_micropy_hw_romfs_part0_start` and `_micropy_hw_romfs_part0_size`,
following existing ports.
Signed-off-by: Damien George <damien@micropython.org>
Signed-off-by: robert-hh <robert@hammelrath.com>
The official mcux-sdk follows a slightly different structure to the
current nxp_sdk submodule, with many drivers moved to a common location.
To ease updating the newer versions of the SDK and/or add new families
the nxp_sdk submodule has been updated to follow the structure of
mcux-sdk, just trimmed down to families used here to considerably
reduce the size.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
Prior to this fix the following would fail:
$ make build-TEENSY40/flexram_config.s
because it didn't create the build directory before generating the file.
Also, make `hal/resethandler_MIMXRT10xx.S` have an explicit dependency on
`flexram_config.s` rather than the latter just being forced to be built
before everything else.
Signed-off-by: Damien George <damien@micropython.org>
The cyw43-driver now provides the Bluetooth initialisation code, making
`drivers/cyw43/cywbt.c` obsolete. To use the new code a port must enable
the `CYW43_ENABLE_BLUETOOTH_OVER_UART` option.
Some ports have yet to migrate to the new code, so in the meantime they can
explicitly add the old source to their source list and continue to use it
without change.
Signed-off-by: Damien George <damien@micropython.org>
Add MSC support using internal flash storage or SD card.
Note this is disabled by default, and can be enabled by boards if needed.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
And use these to initialize the LUT table properly for the various flash
types. The different flash types differ by 3 parameters. Thus it is
easier to just keep one copy of the qspiflash_config structure with the LUT
table and update it during flash initialisation as needed.
Signed-off-by: robert-hh <robert@hammelrath.com>
Allowing to use e.g. the Adafruit bootloaders with MicroPython. The .uf2
file is created in addition to the .bin and .hex files allowing to use the
latter ones without the bootloader for debugging and testing.
Changes:
- Set the location of the ISR Vector and .text segment to 0x6000C000 and
0x6000C400.
- Reserve an area at the start of ITCM for a copy of the interrupt vector
table and copy the table on reset to this place.
- Extend `machine.bootloader()` by setting the magic number to enable the
bootloader on reset.
- Create a .uf2 file which skips the segments below 0x6000C000.
The bootloader has to be installed as a preparation step using the board
specific methods, but then the firmware's .uf2 file version can be
installed using the bootloader. The bootloader can be invoked with:
- double reset
- calling machine.bootloader()
- Using the touch1200 method
Double reset is hard to achieve on MIMXRT boards, since there is no clean
reset pin. Some MIMXRT boards provide it by switching the power.
Some boards are excluded from the .uf2 build:
- MIMXRT1050_EVK: The uf2 bootloader is built for the QSPI version of the
board. MicroPython supports the Hyperflash version.
- MIMXRT1176_EVK: No support for this board yet, but it should be possible.
Signed-off-by: robert-hh <robert@hammelrath.com>
This removes duplicated TinyUSB configuration and port-specific code.
Tested on RT1062, CDC+MSC still working. @robert-hh tested CDC with 1011,
1015, 1020 and 1176.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
Supported triggers are: IRQ_RXIDLE and IRQ_TXIDLE.
When IRQ_RXIDLE is set, the handler will be called 3 character times after
the data in burst stopped.
When IRQ_TXIDLE is set, the handler will be called immediately after the
data has been sent.
This commit requires a change to fsl_lpuart.c, because the existing code
does not support under-run appropriately.
The irq.flags() value is cleared only at an expected event. Do not change
it otherwise.
Signed-off-by: robert-hh <robert@hammelrath.com>
Make can't handle paths with spaces, see https://savannah.gnu.org/bugs/?712
The following workarounds exist:
- When using make's built-in functions:
- Use relative paths wherever possible to avoid spaces in the first
place.
- All spaces in paths can be escaped with backslashes; quotes don't
work.
- Some users use the shell to temporarily rename directories, or to
create symlinks without spaces.
- When using make to pass commands to the system's shell, enclose paths in
quotes. While make will still interpret quoted strings with spaces as
multiple words, the system's shell will correctly parse the resulting
command.
This commit contains the following fixes:
- In ports/stm32/mboot/Makefile: Use relative paths to avoid spaces when
using built-in functions.
- In all other files: Use quotes to enclose paths when make is used to call
shell functions.
All changes have been tested with a directory containing spaces.
Signed-off-by: Iksas <iksas@mailbox.org>
This is a code factoring to have the dict for the machine module in one
location, and all the ports use that same dict. The machine.soft_reset()
function implementation is also factored because it's the same for all
ports that did already implement it. Eventually more functions/bindings
can be factored.
All ports remain functionally the same, except:
- cc3200 port: gains soft_reset, mem8, mem16, mem32, Signal; loses POWER_ON
(which was a legacy constant, replaced long ago by PWRON_RESET)
- nrf port: gains Signal
- qemu-arm port: gains soft_reset
- unix port: gains soft_reset
- zephyr port: gains soft_reset, mem8, mem16, mem32
Signed-off-by: Damien George <damien@micropython.org>
Minor change to remove support for using numeric IDs for machine.Pin. This
was previously based on the index of the pin in the board csv, but this is
different (and incompatible) with other ports.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
All ports now use `--board-csv`, `--prefix`, `--output-souce`,
`--output-header` and no longer write to stdout. This matches the esp32
implementation.
Ports that have an AF input use `--af-csv` (to match `--board-csv`).
Any additional output files are now prefixed with `output-` (e.g.
`--output-af-const`).
Default arguments are removed (all makefiles should always specify all
arguments, using default values is likely an error).
Replaced the `af-defs-cmp-strings` and `hdr-obj-decls` args for stm32 with
just `mboot-mode`. Previously they were set on the regular build, now the
logic is reversed so mboot sets it.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
It's not supported on all ports, adds complexity to the build to generate
pins_af.py, and can mostly be replicated just by printing the pin objects.
Remove support for generating pins_af.py from all ports (nrf, stm32,
renesas-ra, mimxrt, rp2).
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This prevents each port Makefile from having to add an explicit rule for
`build-BOARD/pins_BOARD.c`.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is a code factoring to have the Python bindings in one location, and
all the ports use those same bindings. For all ports except the two listed
below there is no functional change.
The nrf port has UART.sendbreak() removed, but this method previously did
nothing.
The zephyr port has the following methods added:
- UART.init(): supports setting timeout and timeout_char.
- UART.deinit(): does nothing, just returns None.
- UART.flush(): raises OSError(EINVAL) because it's not implemented.
- UART.any() and UART.txdone(): raise NotImplementedError.
Signed-off-by: Damien George <damien@micropython.org>
No functional change, just code factoring to have the Python bindings in
one location, and all the ports use those same bindings.
Signed-off-by: Damien George <damien@micropython.org>
This factors the basic top-level I2S class code from the ports into
extmod/machine_i2s.c:
- I2S class definition and method table.
- The init and deinit method wrappers.
- The make_new code.
Further factoring will follow.
Signed-off-by: Damien George <damien@micropython.org>
There are currently 7 ports that implement machine.WDT and a lot of code is
duplicated across these implementations. This commit factors the common
parts of all these implementations to a single location in
extmod/machine_wdt.c. This common code provides the top-level Python
bindings (class and method wrappers), and then each port implements the
back end specific to that port.
With this refactor the ports remain functionally the same except for:
- The esp8266 WDT constructor now takes keyword arguments, and accepts the
"timeout" argument but raises an exception if it's not the default value
(this port doesn't support changing the timeout).
- The mimxrt and samd ports now interpret the argument to WDT.timeout_ms()
as signed and if it's negative truncate it to the minimum timeout (rather
than it being unsigned and a negative value truncating to the maximum
timeout).
Signed-off-by: Damien George <damien@micropython.org>
By clearing the tamper bits and enabling access to the registers for all
code, just in case that this was set. It keeps the clock running on
battery and the calibration setting.
Signed-off-by: robert-hh <robert@hammelrath.com>
This is option is no longer needed as a Makefile option as the USDHC driver
is enabled for all supported series.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
This is a basic SDIO driver for the mimxrt port, that was added mainly to
support the CYW43 WiFi driver, and as such it only supports the commands
required by the CYW43 driver (but more commands can be added easily). The
driver performs non-blocking DMA transfers, and can detect and recover from
errors.
Note: because the mimxrt port is missing static alternate functions, named
pins and other pin related functions, currently the alternate functions for
USDHC 1 and 2 are hard-coded in the driver.
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
Updates all `help()` output to use the phrase:
`For online docs please visit http://docs.micropython.org/`
Some ports previously used different wording, some pointed to the wrong
link. Also make all ports use `help.c` for consistency.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This one sets the flash image length properly for the teensy loader, such
that the file system is not erased. It was already set in commit
8e54225140 but got lost when the MIMXRT1176
board was added.
Signed-off-by: robert-hh <robert@hammelrath.com>
Separate low level flash access from mimxrt flash driver object. Allows
better abstraction from hardware for testing and reuse in other areas (e.g.
bootloader).
Signed-off-by: Philipp Ebensberger <philipp.ebensberger@3bricks-software.de>
If a board defines a custom bootloader entry function it will be called
first, if not and the ROM API supports RUN bootloader API, then
`machine.bootloader()` will jump to the ROM serial downloader in USB mode.
This allows:
$ make BOARD_DIR=path/to/board
to infer BOARD=board, rather than the previous behavior that required
additionally setting BOARD explicitly.
Also makes the same change for VARIANT_DIR -> VARIANT on Unix.
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Signed-off-by: Damien George <damien@micropython.org>
This drops the `.cpu` directive from the ARM gchelper_*.s files. Having
this directive breaks the linker when targeting older CPUs (e.g. `-mthumb
-mthumb-interwork` for `-mcpu=arm7tdmi`). The actual target CPU should be
determined by the compiler options.
The exact CPU doesn't actually matter, but rather the supported assembly
instruction set. So the files are renamed to *_thumb1.s and *thumb2.s to
indicate the instruction set support instead of the CPU support.
Signed-off-by: David Lechner <david@pybricks.com>
Angus Gratton
robert-hh
Dryw Wade
Andrew Leech
Yilin Sun
iabdalkader
Damien George
Andrew Leech
Iksas
Jim Mussared
Kwabena W. Agyeman
Philipp Ebensberger
David Lechner