mirror of
https://github.com/micropython/micropython.git
synced 2026-01-04 19:20:22 +01:00
6f0193335a
This commit changes the Arduino board identifiers to correspond to their official names. This helps to identify boards at runtime. At the moment the Arduino Portenta H7 is reported as PORTENTA which is unfortunate as now there is another Portenta board (Portenta C33) supported in MicroPython. Also made the other identifiers for flash and network name consistent, removed the incorrectly used MICROPY_PY_SYS_PLATFORM identifiers, and added missing MICROPY_PY_NETWORK_HOSTNAME_DEFAULT identifiers. Boards affected: - stm32: ARDUINO_PORTENTA_H7, ARDUINO_GIGA, ARDUINO_NICLA_VISION - renesas-ra: ARDUINO_PORTENTA_C33 - esp32: ARDUINO_NANO_ESP32 - rp2: ARDUINO_NANO_RP2040_CONNECT Signed-off-by: Sebastian Romero <s.romero@arduino.cc>
246 lines
10 KiB
C
246 lines
10 KiB
C
/*
|
|
* This file is part of the MicroPython project, http://micropython.org/
|
|
* The MIT License (MIT)
|
|
* Copyright (c) 2023 Arduino SA
|
|
*/
|
|
|
|
#define MICROPY_HW_BOARD_NAME "Arduino Nicla Vision"
|
|
#define MICROPY_HW_MCU_NAME "STM32H747"
|
|
#define MICROPY_HW_FLASH_FS_LABEL "Nicla Vision"
|
|
|
|
// Network config
|
|
#define MICROPY_PY_NETWORK_HOSTNAME_DEFAULT "mpy-nicla-vision"
|
|
|
|
#define MICROPY_OBJ_REPR (MICROPY_OBJ_REPR_C)
|
|
#define UINT_FMT "%u"
|
|
#define INT_FMT "%d"
|
|
typedef int mp_int_t; // must be pointer size
|
|
typedef unsigned int mp_uint_t; // must be pointer size
|
|
|
|
#define MICROPY_FATFS_EXFAT (1)
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
#define MICROPY_HW_ENABLE_ADC (1)
|
|
#define MICROPY_HW_ENABLE_DAC (1)
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
|
#define MICROPY_HW_HAS_SWITCH (0)
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
#define MICROPY_HW_ENABLE_SERVO (1)
|
|
#define MICROPY_HW_ENABLE_TIMER (1)
|
|
#define MICROPY_HW_ENABLE_SDCARD (0)
|
|
#define MICROPY_HW_ENABLE_MMCARD (0)
|
|
|
|
// Flash storage config
|
|
#define MICROPY_HW_SPIFLASH_ENABLE_CACHE (1)
|
|
#define MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE (0)
|
|
|
|
#define MICROPY_BOARD_STARTUP NICLAV_board_startup
|
|
void NICLAV_board_startup(void);
|
|
|
|
#define MICROPY_BOARD_EARLY_INIT NICLAV_board_early_init
|
|
void NICLAV_board_early_init(void);
|
|
|
|
#define MICROPY_BOARD_ENTER_BOOTLOADER(nargs, args) NICLAV_board_enter_bootloader()
|
|
void NICLAV_board_enter_bootloader(void);
|
|
|
|
void NICLAV_board_low_power(int mode);
|
|
#define MICROPY_BOARD_LEAVE_STOP NICLAV_board_low_power(0);
|
|
#define MICROPY_BOARD_ENTER_STOP NICLAV_board_low_power(1);
|
|
#define MICROPY_BOARD_ENTER_STANDBY NICLAV_board_low_power(2);
|
|
|
|
void NICLAV_board_osc_enable(int enable);
|
|
#define MICROPY_BOARD_OSC_ENABLE NICLAV_board_osc_enable(1);
|
|
#define MICROPY_BOARD_OSC_DISABLE NICLAV_board_osc_enable(0);
|
|
|
|
// PLL1 400MHz/50MHz for SDMMC and FDCAN
|
|
// USB and RNG are clocked from the HSI48
|
|
#define MICROPY_HW_CLK_PLLM (5)
|
|
#define MICROPY_HW_CLK_PLLN (160)
|
|
#define MICROPY_HW_CLK_PLLP (2)
|
|
#define MICROPY_HW_CLK_PLLQ (16)
|
|
#define MICROPY_HW_CLK_PLLR (2)
|
|
#define MICROPY_HW_CLK_PLLVCI (RCC_PLL1VCIRANGE_2)
|
|
#define MICROPY_HW_CLK_PLLVCO (RCC_PLL1VCOWIDE)
|
|
#define MICROPY_HW_CLK_PLLFRAC (0)
|
|
|
|
// PLL2 200MHz for FMC and QSPI.
|
|
#define MICROPY_HW_CLK_PLL2M (5)
|
|
#define MICROPY_HW_CLK_PLL2N (80)
|
|
#define MICROPY_HW_CLK_PLL2P (2)
|
|
#define MICROPY_HW_CLK_PLL2Q (2)
|
|
#define MICROPY_HW_CLK_PLL2R (2)
|
|
#define MICROPY_HW_CLK_PLL2VCI (RCC_PLL2VCIRANGE_2)
|
|
#define MICROPY_HW_CLK_PLL2VCO (RCC_PLL2VCOWIDE)
|
|
#define MICROPY_HW_CLK_PLL2FRAC (0)
|
|
|
|
// PLL3 160MHz for ADC and SPI123
|
|
#define MICROPY_HW_CLK_PLL3M (5)
|
|
#define MICROPY_HW_CLK_PLL3N (160)
|
|
#define MICROPY_HW_CLK_PLL3P (2)
|
|
#define MICROPY_HW_CLK_PLL3Q (5)
|
|
#define MICROPY_HW_CLK_PLL3R (2)
|
|
#define MICROPY_HW_CLK_PLL3VCI (RCC_PLL3VCIRANGE_2)
|
|
#define MICROPY_HW_CLK_PLL3VCO (RCC_PLL3VCOWIDE)
|
|
#define MICROPY_HW_CLK_PLL3FRAC (0)
|
|
|
|
// HSE in BYPASS mode.
|
|
#define MICROPY_HW_CLK_USE_BYPASS (1)
|
|
|
|
// Bus clock divider values
|
|
#define MICROPY_HW_CLK_AHB_DIV (RCC_HCLK_DIV2)
|
|
#define MICROPY_HW_CLK_APB1_DIV (RCC_APB1_DIV2)
|
|
#define MICROPY_HW_CLK_APB2_DIV (RCC_APB2_DIV2)
|
|
#define MICROPY_HW_CLK_APB3_DIV (RCC_APB3_DIV2)
|
|
#define MICROPY_HW_CLK_APB4_DIV (RCC_APB4_DIV2)
|
|
|
|
// Peripheral clock sources
|
|
#define MICROPY_HW_RCC_HSI48_STATE (RCC_HSI48_ON)
|
|
#define MICROPY_HW_RCC_USB_CLKSOURCE (RCC_USBCLKSOURCE_HSI48)
|
|
#define MICROPY_HW_RCC_RTC_CLKSOURCE (RCC_RTCCLKSOURCE_LSI)
|
|
#define MICROPY_HW_RCC_FMC_CLKSOURCE (RCC_FMCCLKSOURCE_PLL2)
|
|
#define MICROPY_HW_RCC_RNG_CLKSOURCE (RCC_RNGCLKSOURCE_HSI48)
|
|
#define MICROPY_HW_RCC_ADC_CLKSOURCE (RCC_ADCCLKSOURCE_PLL3)
|
|
#define MICROPY_HW_RCC_SDMMC_CLKSOURCE (RCC_SDMMCCLKSOURCE_PLL)
|
|
#define MICROPY_HW_RCC_FDCAN_CLKSOURCE (RCC_FDCANCLKSOURCE_PLL)
|
|
#define MICROPY_HW_RCC_SPI123_CLKSOURCE (RCC_SPI123CLKSOURCE_PLL3)
|
|
#define MICROPY_HW_RCC_I2C123_CLKSOURCE (RCC_I2C123CLKSOURCE_D2PCLK1)
|
|
#define MICROPY_HW_RCC_QSPI_CLKSOURCE (RCC_QSPICLKSOURCE_PLL2)
|
|
|
|
// SMPS configuration
|
|
#define MICROPY_HW_PWR_SMPS_CONFIG (PWR_LDO_SUPPLY)
|
|
|
|
// Configure the analog switches for dual-pad pins.
|
|
#define MICROPY_HW_ANALOG_SWITCH_PA0 (SYSCFG_SWITCH_PA0_OPEN)
|
|
#define MICROPY_HW_ANALOG_SWITCH_PA1 (SYSCFG_SWITCH_PA1_OPEN)
|
|
// PC2_C and PC3_C, which are connected to ULPI NXT and DIR pins.
|
|
#define MICROPY_HW_ANALOG_SWITCH_PC2 (SYSCFG_SWITCH_PC2_CLOSE)
|
|
#define MICROPY_HW_ANALOG_SWITCH_PC3 (SYSCFG_SWITCH_PC3_CLOSE)
|
|
|
|
// There is an external 32kHz oscillator
|
|
#define RTC_ASYNCH_PREDIV (0)
|
|
#define RTC_SYNCH_PREDIV (0x7fff)
|
|
#define MICROPY_HW_RTC_USE_BYPASS (1)
|
|
#define MICROPY_HW_RTC_USE_US (1)
|
|
#define MICROPY_HW_RTC_USE_CALOUT (1)
|
|
|
|
#if !MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE
|
|
// QSPI flash for storage
|
|
#define MICROPY_HW_QSPI_PRESCALER (2) // 100MHz
|
|
#define MICROPY_HW_QSPIFLASH_SIZE_BITS_LOG2 (27)
|
|
// Reserve 1MiB at the end for compatibility with alternate firmware that places WiFi blob here.
|
|
#define MICROPY_HW_SPIFLASH_SIZE_BITS (120 * 1024 * 1024)
|
|
#define MICROPY_HW_QSPIFLASH_CS (pyb_pin_QSPI2_CS)
|
|
#define MICROPY_HW_QSPIFLASH_SCK (pyb_pin_QSPI2_CLK)
|
|
#define MICROPY_HW_QSPIFLASH_IO0 (pyb_pin_QSPI2_D0)
|
|
#define MICROPY_HW_QSPIFLASH_IO1 (pyb_pin_QSPI2_D1)
|
|
#define MICROPY_HW_QSPIFLASH_IO2 (pyb_pin_QSPI2_D2)
|
|
#define MICROPY_HW_QSPIFLASH_IO3 (pyb_pin_QSPI2_D3)
|
|
|
|
// SPI flash #1, block device config
|
|
extern const struct _mp_spiflash_config_t spiflash_config;
|
|
extern struct _spi_bdev_t spi_bdev;
|
|
#define MICROPY_HW_BDEV_SPIFLASH (&spi_bdev)
|
|
#define MICROPY_HW_BDEV_SPIFLASH_CONFIG (&spiflash_config)
|
|
#define MICROPY_HW_BDEV_SPIFLASH_SIZE_BYTES (MICROPY_HW_SPIFLASH_SIZE_BITS / 8)
|
|
#define MICROPY_HW_BDEV_SPIFLASH_EXTENDED (&spi_bdev)
|
|
#endif
|
|
|
|
// 4 wait states
|
|
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_2
|
|
|
|
// UART config
|
|
#define MICROPY_HW_UART1_TX (pyb_pin_BT_TXD)
|
|
#define MICROPY_HW_UART1_RX (pyb_pin_BT_RXD)
|
|
#define MICROPY_HW_UART1_RTS (pyb_pin_BT_RTS)
|
|
#define MICROPY_HW_UART1_CTS (pyb_pin_BT_CTS)
|
|
|
|
#define MICROPY_HW_UART4_TX (pin_B9)
|
|
#define MICROPY_HW_UART4_RX (pin_B8)
|
|
|
|
// LPUART1 config
|
|
#define MICROPY_HW_LPUART1_TX (pin_A9)
|
|
#define MICROPY_HW_LPUART1_RX (pin_A10)
|
|
|
|
// I2C buses
|
|
#define MICROPY_HW_I2C1_SCL (pin_B8)
|
|
#define MICROPY_HW_I2C1_SDA (pin_B9)
|
|
|
|
#define MICROPY_HW_I2C2_SCL (pin_F1)
|
|
#define MICROPY_HW_I2C2_SDA (pin_F0)
|
|
|
|
#define MICROPY_HW_I2C3_SCL (pin_A8)
|
|
#define MICROPY_HW_I2C3_SDA (pin_C9)
|
|
|
|
// SPI buses
|
|
#define MICROPY_HW_SPI4_NSS (pin_E11)
|
|
#define MICROPY_HW_SPI4_SCK (pin_E12)
|
|
#define MICROPY_HW_SPI4_MISO (pin_E13)
|
|
#define MICROPY_HW_SPI4_MOSI (pin_E14)
|
|
|
|
#define MICROPY_HW_SPI5_NSS (pin_F6)
|
|
#define MICROPY_HW_SPI5_SCK (pin_F7)
|
|
#define MICROPY_HW_SPI5_MISO (pin_F8)
|
|
#define MICROPY_HW_SPI5_MOSI (pin_F11)
|
|
|
|
// FDCAN bus
|
|
#define MICROPY_HW_CAN1_NAME "FDCAN1"
|
|
#define MICROPY_HW_CAN1_TX (pin_A10)
|
|
#define MICROPY_HW_CAN1_RX (pin_A9)
|
|
#define MICROPY_HW_CAN_IS_RESERVED(id) (id != PYB_CAN_1)
|
|
|
|
// LEDs
|
|
#define MICROPY_HW_LED1 (pyb_pin_LED_RED) // red
|
|
#define MICROPY_HW_LED2 (pyb_pin_LED_GREEN) // green
|
|
#define MICROPY_HW_LED3 (pyb_pin_LED_BLUE) // yellow
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_low(pin))
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_high(pin))
|
|
|
|
// WiFi SDMMC
|
|
#define MICROPY_HW_SDIO_SDMMC (2)
|
|
#define MICROPY_HW_SDIO_CK (pin_D6)
|
|
#define MICROPY_HW_SDIO_CMD (pin_D7)
|
|
#define MICROPY_HW_SDIO_D0 (pin_B14)
|
|
#define MICROPY_HW_SDIO_D1 (pin_B15)
|
|
#define MICROPY_HW_SDIO_D2 (pin_G11)
|
|
#define MICROPY_HW_SDIO_D3 (pin_B4)
|
|
|
|
// USB config
|
|
#define MICROPY_HW_USB_HS (1)
|
|
#define MICROPY_HW_USB_HS_ULPI_NXT (pin_C3)
|
|
#define MICROPY_HW_USB_HS_ULPI_STP (pin_C0)
|
|
#define MICROPY_HW_USB_HS_ULPI_DIR (pin_C2)
|
|
#define MICROPY_HW_USB_HS_ULPI3320 (1)
|
|
|
|
#define MICROPY_HW_USB_CDC_RX_DATA_SIZE (1024)
|
|
#define MICROPY_HW_USB_CDC_TX_DATA_SIZE (1024)
|
|
#define MICROPY_HW_USB_CDC_1200BPS_TOUCH (1)
|
|
#define GPIO_AF10_OTG_HS (GPIO_AF10_OTG2_HS)
|
|
|
|
// Bluetooth config
|
|
#define MICROPY_HW_BLE_UART_ID (PYB_UART_1)
|
|
#define MICROPY_HW_BLE_UART_BAUDRATE (115200)
|
|
#define MICROPY_HW_BLE_UART_BAUDRATE_SECONDARY (3000000)
|
|
#define MICROPY_HW_BLE_UART_BAUDRATE_DOWNLOAD_FIRMWARE (3000000)
|
|
|
|
#define MICROPY_HW_USB_VID 0x2341
|
|
#define MICROPY_HW_USB_PID 0x045F
|
|
#define MICROPY_HW_USB_PID_CDC_MSC (MICROPY_HW_USB_PID)
|
|
#define MICROPY_HW_USB_PID_CDC_HID (MICROPY_HW_USB_PID)
|
|
#define MICROPY_HW_USB_PID_CDC (MICROPY_HW_USB_PID)
|
|
#define MICROPY_HW_USB_PID_MSC (MICROPY_HW_USB_PID)
|
|
#define MICROPY_HW_USB_PID_CDC2_MSC (MICROPY_HW_USB_PID)
|
|
#define MICROPY_HW_USB_PID_CDC2 (MICROPY_HW_USB_PID)
|
|
#define MICROPY_HW_USB_PID_CDC3 (MICROPY_HW_USB_PID)
|
|
#define MICROPY_HW_USB_PID_CDC3_MSC (MICROPY_HW_USB_PID)
|
|
#define MICROPY_HW_USB_PID_CDC_MSC_HID (MICROPY_HW_USB_PID)
|
|
#define MICROPY_HW_USB_PID_CDC2_MSC_HID (MICROPY_HW_USB_PID)
|
|
#define MICROPY_HW_USB_PID_CDC3_MSC_HID (MICROPY_HW_USB_PID)
|
|
#define MICROPY_HW_USB_LANGID_STRING 0x409
|
|
#define MICROPY_HW_USB_MANUFACTURER_STRING "Arduino"
|
|
#define MICROPY_HW_USB_PRODUCT_FS_STRING "Nicla Vision Virtual Comm Port in FS Mode"
|
|
#define MICROPY_HW_USB_PRODUCT_HS_STRING "Nicla Vision Virtual Comm Port in HS Mode"
|
|
#define MICROPY_HW_USB_INTERFACE_FS_STRING "Nicla Vision Interface"
|
|
#define MICROPY_HW_USB_INTERFACE_HS_STRING "Nicla Vision Interface"
|
|
#define MICROPY_HW_USB_CONFIGURATION_FS_STRING "Nicla Vision Config"
|
|
#define MICROPY_HW_USB_CONFIGURATION_HS_STRING "Nicla Vision Config"
|