micropython/docs/zephyr/quickref.rst

.. _zephyr_quickref:

Quick reference for the Zephyr port
===================================

Below is a quick reference for the Zephyr port. If it is your first time working with this port please consider reading the following sections first:

.. toctree::
   :maxdepth: 1

   general.rst
   tutorial/index.rst

Running MicroPython
-------------------

See the corresponding section of the tutorial: :ref:`intro`.

Delay and timing
----------------

Use the :mod:`time <time>` module::

    import time

    time.sleep(1)               # sleep for 1 second
    time.sleep_ms(500)          # sleep for 500 milliseconds
    time.sleep_us(10)           # sleep for 10 microseconds
    start = time.ticks_ms()     # get millisecond counter
    delta = time.ticks_diff(time.ticks_ms(), start) # compute time difference

Pins and GPIO
-------------

Use the :ref:`machine.Pin <machine.Pin>` class::

    from machine import Pin

    pin = Pin(("gpiob", 21), Pin.IN)    # create input pin on GPIO port B
    print(pin)                          # print pin port and number

    pin.init(Pin.OUT, Pin.PULL_UP, value=1)     # reinitialize pin

    pin.value(1)                        # set pin to high
    pin.value(0)                        # set pin to low

    pin.on()                            # set pin to high
    pin.off()                           # set pin to low

    pin = Pin(("gpiob", 21), Pin.IN)              # create input pin on GPIO port B

    pin = Pin(("gpiob", 21), Pin.OUT, value=1)    # set pin high on creation

    pin = Pin(("gpiob", 21), Pin.IN, Pin.PULL_UP) # enable internal pull-up resistor

    switch = Pin(("gpioc", 6), Pin.IN)            # create input pin for a switch
    switch.irq(lambda t: print("SW2 changed"))    # enable an interrupt when switch state is changed

PWM
---

Use the :ref:`machine.PWM <machine.PWM>` class::

    from machine import PWM

    pwm = PWM(("pwm0", 0), freq=3921568, duty_ns=200, invert=True)    # create pwm on PWM0
    print(pwm)                                                        # print pwm

    print(pwm.duty_ns())                                              # print pwm duty cycle in nanoseconds
    pwm.duty_ns(255)                                                  # set new pwm duty cycle in nanoseconds

    pwm.deinit()

Hardware I2C bus
----------------

Hardware I2C is accessed via the :ref:`machine.I2C <machine.I2C>` class::

    from machine import I2C

    i2c = I2C("i2c0")           # construct an i2c bus
    print(i2c)                  # print device name

    i2c.scan()                  # scan the device for available I2C slaves

    i2c.readfrom(0x1D, 4)                # read 4 bytes from slave 0x1D
    i2c.readfrom_mem(0x1D, 0x0D, 1)      # read 1 byte from slave 0x1D at slave memory 0x0D

    i2c.writeto(0x1D, b'abcd')           # write to slave with address 0x1D
    i2c.writeto_mem(0x1D, 0x0D, b'ab')   # write to slave 0x1D at slave memory 0x0D

    buf = bytearray(8)                  # create buffer of size 8
    i2c.writeto(0x1D, b'abcd')          # write buf to slave 0x1D

Hardware SPI bus
----------------

Hardware SPI is accessed via the :ref:`machine.SPI <machine.SPI>` class::

    from machine import SPI

    spi = SPI("spi0")           # construct a SPI bus with default configuration
    spi.init(baudrate=100000, polarity=0, phase=0, bits=8, firstbit=SPI.MSB) # set configuration

    # equivalently, construct the SPI bus and set configuration at the same time
    spi = SPI("spi0", baudrate=100000, polarity=0, phase=0, bits=8, firstbit=SPI.MSB)
    print(spi)                  # print device name and bus configuration

    spi.read(4)                 # read 4 bytes on MISO
    spi.read(4, write=0xF)      # read 4 bytes while writing 0xF on MOSI

    buf = bytearray(8)          # create a buffer of size 8
    spi.readinto(buf)           # read into the buffer (reads number of bytes equal to the buffer size)
    spi.readinto(buf, 0xF)      # read into the buffer while writing 0xF on MOSI

    spi.write(b'abcd')          # write 4 bytes on MOSI

    buf = bytearray(4)                  # create buffer of size 8
    spi.write_readinto(b'abcd', buf)    # write to MOSI and read from MISO into the buffer
    spi.write_readinto(buf, buf)        # write buf to MOSI and read back into the buf

Analog to Digital Converter (ADC)
----------------------------------

Use the :ref:`machine.ADC <machine.ADC>` class.

Example of using ADC to read a pin's analog value (the ``zephyr,user`` node must contain
the ``io-channels`` property containing all the ADC channels)::

    from machine import ADC

    adc = ADC(("adc", 0))
    adc.read_uv()

Disk Access
-----------

Use the :ref:`zephyr.DiskAccess <zephyr.DiskAccess>` class to support filesystem::

    import vfs
    from zephyr import DiskAccess

    block_dev = DiskAccess('SDHC')      # create a block device object for an SD card
    vfs.VfsFat.mkfs(block_dev)          # create FAT filesystem object using the disk storage block
    vfs.mount(block_dev, '/sd')         # mount the filesystem at the SD card subdirectory

    # with the filesystem mounted, files can be manipulated as normal
    with open('/sd/hello.txt','w') as f:     # open a new file in the directory
        f.write('Hello world')                  # write to the file
    print(open('/sd/hello.txt').read())      # print contents of the file

Flash Area
----------

Use the :ref:`zephyr.FlashArea <zephyr.FlashArea>` class to support filesystem::

    import vfs
    from zephyr import FlashArea

    block_dev = FlashArea(4, 4096)      # creates a block device object in the frdm-k64f flash scratch partition
    vfs.VfsLfs2.mkfs(block_dev)         # create filesystem in lfs2 format using the flash block device
    vfs.mount(block_dev, '/flash')      # mount the filesystem at the flash subdirectory

    # with the filesystem mounted, files can be manipulated as normal
    with open('/flash/hello.txt','w') as f:     # open a new file in the directory
        f.write('Hello world')                  # write to the file
    print(open('/flash/hello.txt').read())      # print contents of the file

The ``FlashAreas``' IDs that are available are listed in the FlashArea module, as ``ID_*``.

Sensor
------

Use the :ref:`zsensor.Sensor <zsensor.Sensor>` class to access sensor data::

    import zsensor
    from zsensor import Sensor

    accel = Sensor("fxos8700")    # create sensor object for the accelerometer

    accel.measure()               # obtain a measurement reading from the accelerometer

    # each of these prints the value taken by measure()
    accel.get_float(zsensor.ACCEL_X)  # print measurement value for accelerometer X-axis sensor channel as float
    accel.get_millis(zsensor.ACCEL_Y) # print measurement value for accelerometer Y-axis sensor channel in millionths
    accel.get_micro(zsensor.ACCEL_Z)  # print measurement value for accelerometer Z-axis sensor channel in thousandths
    accel.get_int(zsensor.ACCEL_X)    # print measurement integer value only for accelerometer X-axis sensor channel

The channel IDs that are used as arguments to the :meth:`zsensor.Sensor.get_int`,
:meth:`zsensor.Sensor.get_float()`, :meth:`zsensor.Sensor.get_millis()`, and
:meth:`zsensor.Sensor.get_micros()` methods are constants in the :mod:`zsensor` module.

You can use the :meth:`zsensor.Sensor.attr_set` method to set sensor attributes
like full-scale range and update rate::

    # Example for XIAO BLE NRF52840 SENSE
    from zsensor import *
    accel = Sensor('lsm6ds3tr_c')  # name from Devicetree
    # Set full-scale to 2g (19.613300 m/sec^2)
    # units are micro-m/s^2 (given as a float)
    accel.attr_set(ACCEL_XYZ, ATTR_FULL_SCALE, 19.613300)
    # Set sampling frequency to 104 Hz (as a pair of integers)
    accel.attr_set(ACCEL_XYZ, ATTR_SAMPLING_FREQUENCY, 104, 0)
    accel.measure()
    accel.get_float(ACCEL_X) # -0.508 (m/s^2)
    accel.get_float(ACCEL_Y) # -3.62 (m/s^2)
    accel.get_float(ACCEL_Z) # 9.504889 (m/s^2)

There are also the :meth:`zsensor.Sensor.attr_get_float`, :meth:`zsensor.Sensor.attr_get_int`,
:meth:`zsensor.Sensor.attr_get_millis`, and :meth:`zsensor.Sensor.attr_get_micros` methods,
but many sensors do not support these::

    full_scale = accel.attr_get_float(ATTR_FULL_SCALE)

The attribute IDs that are used as arguments to the :meth:`zsensor.Sensor.attr_set`,
:meth:`zsensor.Sensor.attr_get_float`, :meth:`zsensor.Sensor.attr_get_int`,
:meth:`zsensor.Sensor.attr_get_millis`, and :meth:`zsensor.Sensor.attr_get_micros`
methods are constants in the :mod:`zsensor` module named ``ATTR_*``.