16379 Commits

This Branch

This Branch

All Branches

Author	SHA1	Message	Date
Jared Hancock	078ead24f3	extmod/network_wiznet5k: Reset mDNS when interface is brought up. ... The LwIP interface is removed in wiznet5k_deinit() which is called as part of the init sequence. Therefore, if using mDNS, then the interface will need to be re-added when bringing the interface up. Additionally, this allows to set the hostname from MicroPython code prior to bringing the interface up and mDNS responding to the (new) hostname. This allows the hostname to be configured and saved on the flash or be based on dynamic information such as the MAC or unique_id(). Signed-off-by: Jared Hancock <jared.hancock@centeredsolutions.com>	2024-10-23 16:29:28 +11:00
Damien George	3f54e5dff2	tests/extmod: Support esp32,mimxrt,stm32,samd ports in UART TX test. ... Getting this test running on stm32- and mimxrt-based boards requires adding a small delay after constructing the UART so that the initial idle frame has time to be transmitted before the test starts. Also, the timing margin needs to account for an additional 1-bit worth of time on some MCUs. Thanks to @robert-hh for the esp32, mimxrt and samd settings. Signed-off-by: Damien George <damien@micropython.org>	2024-10-22 22:21:17 +11:00
Alessandro Gatti	6328958a39	rp2/mpconfigport: Leave callable pointers alone on RV32. ... The port configuration file tagged callable pointers' LSB on both Arm and RISC-V variants. This is needed on Arm due to Thumb/Thumb2 code addresses having their LSB set, but on RISC-V this is not required. Signed-off-by: Alessandro Gatti <a.gatti@frob.it>	2024-10-22 15:01:53 +11:00
Plaque FCC	324871f380	qemu/mcu/rv32: Fix test of mcause value in lookup_cause. ... Signed-off-by: Plaque FCC <plaque-fcc@github>	2024-10-22 14:52:01 +11:00
Volodymyr Shymanskyy	8fef67bda5	esp32/modmachine: Allow building with USB CDC disabled. ... Signed-off-by: Volodymyr Shymanskyy <vshymanskyi@gmail.com>	2024-10-22 14:45:51 +11:00
Damien George	0646177997	tests/extmod: Make invalid-blockdev test work consistently on all ports. ... Some ports (eg stm32) configure the FAT driver differently (eg with multi-partition support) and that leads to a slightly different sequence of block reads, compared to other configurations (eg rp2). Comment out the printing in `readblocks()` so the tests are deterministic (the printing is still useful for debugging). Signed-off-by: Damien George <damien@micropython.org>	2024-10-22 14:32:51 +11:00
Damien George	f7abb52847	tests/run-tests.py: Skip large viper test on esp8266. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-22 14:31:13 +11:00
Damien George	52f2ba5677	tests/micropython: Tweak ringio test for targets with terse errors. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-22 14:31:13 +11:00
Damien George	1e3b24238e	tests/extmod: Adjust ssl/tls tests to run on targets with axTLS. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-22 14:31:13 +11:00
Damien George	7d442373af	tests/extmod: Config SPI test for esp8266 and skip SoftTimer test. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-22 14:31:13 +11:00
Corran Webster	d1574de3b6	extmod/modframebuf: Fix FrameBuffer size check for stride corner-cases. ... This is a fix for issue #15944, and handles corner cases in the FrameBuffer code when using stride values where the last line's stride may extend past the end of the underlying buffer. This commit includes extra tests for these corner cases. For example a GS8 format FrameBuffer with a width of 8, height of 2 and stride of 10 should be able to fit into a buffer of size 18 (10 bytes for the first horizontal line, and 8 bytes for the second -- the full 10 bytes are not needed). Similarly a 1 by 9 FrameBuffer in MONO_VLSB format with a stride of 10 should be able to fit into a buffer of length 11 (10 bytes for the first 8 lines, and then one byte for the 9th line. Being able to do this is particularly important when cropping the corner of an existing FrameBuffer, either to copy a sprite or to clip drawing. Signed-off-by: Corran Webster <cwebster@unital.dev>	2024-10-22 13:05:31 +11:00
Damien George	7ed480fc6f	Revert "stm32/machine_uart: Allow changing only the baudrate." ... This reverts commit c94a3205b0. The idea behind this reverted commit was that it allowed to reconfigure the UART to change only the baudrate, which is important in the context of a PPP connection where the baudrate may be changed as part of the protocol. Also, other ports like the rp2 port have this behaviour, where individual parameters of the UART can be changed with the `.init()` method. But this commit was no good for a few reasons: 1. It's a subtle breaking change to the UART API, because existing code that constructs or initialises a UART with just the baudrate would expect all other parameters to be reset to their defaults. But with this commit those parameters would remain unchanged. 2. Constructing a UART like `UART(1, 9600)` also hits this code path of only changing the baudrate and does not reset other parameters, which is unexpected. 3. It doesn't support setting the baudrate via keyword, eg `UART.init(baudrate=9600)`. 4. The `timeout_char` field is not updated when changing only the baudrate, which can lead to unexpected timeouts when reading/writing. Due to point (4), this commit broke the `tests/ports/stm32/uart.py` test, the `uart.writechar(1)` has a timeout because the `uart.init(2400)` does not set the `timeout_char` for the new baudrate. Points (2)-(4) could be fixed, but point (1) (being a breaking change) would remain as an issue. So the commit is reverted. Signed-off-by: Damien George <damien@micropython.org>	2024-10-22 11:50:05 +11:00
Damien George	97af1001ae	rp2/machine_uart: Make it so TX is done only when no longer busy. ... Prior to this commit, when flushing a UART on the rp2 port, it returns just before the last character is sent out the wire. Fix this by waiting until the BUSY flag is cleared. This also fixes the behaviour of `UART.txdone()` to return `True` only when the last byte has gone out. Updated docs and tests to match. The test now checks that UART TX time is very close to the expected time (prior, it was just testing that the TX time was less than the expected time). Signed-off-by: Damien George <damien@micropython.org>	2024-10-22 10:17:05 +11:00
Damien George	1b89c503db	py/objtype: Don't delegate lookup of descriptor methods to __getattr__. ... When descriptors are enabled, lookup of the `__get__`, `__set__` and `__delete__` descriptor methods should not be delegated to `__getattr__`. That follows CPython behaviour. Signed-off-by: Damien George <damien@micropython.org>	2024-10-16 15:03:30 +11:00
Andrew Leech	3fecab58a0	esp32/mphalport: Always poll stdin ring-buffer to include UART use. ... This fixes a regression introduced in commit 4247921c4e, where this ring-buffer polling was accidentally put inside the `#if MICROPY_HW_ESP_USB_SERIAL_JTAG`. Signed-off-by: Andrew Leech <andrew@alelec.net>	2024-10-16 14:50:11 +11:00
Damien George	838f21298a	unix/main: Add --version command-line option. ... CPython also has this option. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 14:44:10 +11:00
Damien George	51663b9aa7	rp2/machine_uart: Clear timeout_char when UART is first constructed. ... Otherwise a previous value of `timeout_char` may be left over after a soft reset. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:23:06 +11:00
Damien George	b33f64792f	tests/run-tests.py: Only run inlineasm tests on rp2 ARM targets. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:23:06 +11:00
Damien George	b42bb911c6	tests/ports/rp2: Update lightsleep/machine_idle to skip on RP2350. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:23:06 +11:00
Damien George	651b63cd79	tests/ports/rp2: Add simple rp2-specific UART test. ... To test construction of UART instances. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:23:06 +11:00
Damien George	fda7ae83a8	tests/ports/rp2: Update DMA test to work on RP2350. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:21:10 +11:00
Damien George	f9cebe676e	tools/ci.sh: Add RPI_PICO2 to CI. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:21:10 +11:00
Peter Harper	e32e13f7e4	rp2/boards/RPI_PICO2: Add new RPI_PICO2 board definition. ... This is the same form-factor as the Pico but with an RP2350. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:20:12 +11:00
Damien George	137e9e8c79	rp2/main: Set CPU frequency to default for the MCU. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:20:12 +11:00
Phil Howard	27904ae4b9	rp2/machine_pwm: Add RP2350 slices to machine.PWM. ... Signed-off-by: Phil Howard <phil@gadgetoid.com>	2024-10-15 12:19:52 +11:00
Angus Gratton	8cc7c64d01	rp2: Workaround pico_aon_timer timezone binary size increase. ... Provide stub implementations of localtime_r() and mktime() to avoid code size increase. Reported upstream at https://github.com/raspberrypi/pico-sdk/issues/1810 This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-10-15 12:18:53 +11:00
Damien George	fa15ae4503	rp2/machine_bitstream: Implement bitstream for RISC-V using mcycle. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:18:51 +11:00
Damien George	ea2eed1b23	rp2/mphalport: Implement mp_hal_ticks_cpu for RISCV using mcycle. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:18:32 +11:00
Dryw Wade	957cea23d5	rp2/machine_uart: Allow new TX/RX pins on RP2350. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:18:32 +11:00
Dryw Wade	7a78e5ae7c	rp2/machine_bitstream: Set SysTick reset value. ... In case it doesn't have the correct value. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:18:29 +11:00
Damien George	f2f08ef2d9	rp2/Makefile: Allow CMAKE_ARGS to be set by user. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:16:46 +11:00
Damien George	4fc6cf9141	rp2: Add support for RP2350 in RISCV mode. ... As part of this change, the RV32I native emitter is enabled on RISCV board variants. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:16:46 +11:00
Phil Howard	34e463d861	rp2/machine_adc: Add ADC support for RP2350B. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:16:46 +11:00
Peter Harper	d0bc42796b	rp2/clocks_extra: Update runtime_clocks_init based on new pico-sdk. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:15:48 +11:00
Phil Howard	57f4cabff9	rp2/machine_pin: Generalise gpio_irq handler for pins >32. ... Fix the gpio_irq function so that it looks at all six iobank0_hw->intr[n] registers, for up to 48 IOs. Signed-off-by: Phil Howard <phil@gadgetoid.com>	2024-10-15 12:14:59 +11:00
Peter Harper	733052f6b9	rp2/machine_pin: Use 64-bit gpio functions to allow gpios >=32 to work. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:14:25 +11:00
Peter Harper	4af09de19c	rp2/boards/make-pins.py: Pass num-gpios/num-ext-gpios into make-pins. ... NUM_GPIOS amd NUM_EXT_GPIOS are currently hardcoded in make-pins.py, which makes it difficult to support SoCs with different pin count. This commit generalises make-pins.py by passing in the pin count in via the new arguments `--num-gpios` and `--num-ext-gpios`. These default to the current values supported by Pico, namely 30/10. This can be changed with PICO_NUM_GPIOS and PICO_NUM_EXT_GPIOS in `mpconfigboard.cmake`. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:12:04 +11:00
Phil Howard	e6093c0fbd	rp2/rp2_pio: Add support for RP2350A/B variants in PIO interface. ... Add support for 32 and 48 pin variants of RP2350. Add new `PIO.gpio_base()` method, mirroring the Pico SDK. Signed-off-by: Phil Howard <phil@gadgetoid.com> Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:09:48 +11:00
Damien George	a3d1c59ca3	rp2/machine_pin: Move decl of machine_pin_obj_table to public header. ... So other code can include `machine_pin.h` and use the pin name macros such as `pin_GPIO0`. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 12:09:48 +11:00
Phil Howard	6d39418f69	rp2: Add support for 48-pin RP2350 variant. ... Update NUM_GPIOS to match NUM_BANK0_GPIOS, and increase bit-width of variables that store pin numbers. Signed-off-by: Phil Howard <phil@gadgetoid.com>	2024-10-15 12:08:39 +11:00
Peter Harper	d2c85c74da	rp2: Integrate RP2350 and use aon_timer instead of rtc API. ... This commit separates various build settings and include files that are specific to RP2040 and RP2350, and uses the aon_timer interface instead of rtc, to work across both MCU variants. Signed-off-by: Damien George <damien@micropython.org> Signed-off-by: Phil Howard <phil@gadgetoid.com>	2024-10-15 12:07:59 +11:00
Peter Harper	27aeade832	rp2/rp2_dma: Generalise DMA for RP2350. ... Two new bits were added to the ctrl register, and existing bits were shifted, so use DMA_CH0_CTRL_TRIG_xxx constants to generalise the code. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 11:57:06 +11:00
Peter Harper	d1423ef7a2	rp2/modmachine: Implement lightsleep for RP2350. ... This isn't fully working, the CPU often wakes up early. That will be fixed when a newer version of pico-sdk is released. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 11:56:27 +11:00
Peter Harper	c90d996c9d	rp2: Update custom linker scripts for new pico-sdk. ... Signed-off-by: Phil Howard <phil@gadgetoid.com> Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 11:51:56 +11:00
Peter Harper	815d6a131d	rp2/mpconfigport: Set MCU name for RP2350. ... Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 11:51:56 +11:00
Damien George	70a884d6ec	lib/pico-sdk: Update to version 2.0.0. ... Adds support for the new RP2350 MCU. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 11:51:56 +11:00
Phil Howard	525fce7170	py/usermod.cmake: Check target exists in usermod_gather_sources. ... Check a target exists before accessing properties. Otherwise usermod_gather_sources would recurse into garbage property names and break. Signed-off-by: Phil Howard <phil@gadgetoid.com>	2024-10-15 11:51:56 +11:00
Ayush Singh	fa942d532f	zephyr/boards: Add support for BeagleConnect Freedom. ... Enable the following capabilities: I2C, SPI, FLASH. Signed-off-by: Ayush Singh <ayush@beagleboard.org>	2024-10-15 11:44:42 +11:00
Damien George	d92694c3e8	tools: Only issue a single Ctrl-C when entering raw REPL. ... A long time ago when there was only the `stm` port, Ctrl-C would trigger a preemptive NLR jump to break out of running code. Then in commit 124df6f8d0 a more general approach to asynchronous `KeyboardInterrupt` exceptions was implemented, and `stmhal` supported both approaches, with the general (soft) interrupt taking priority. Then in commit bc1488a05f `pyboard.py` was updated with a corresponding change to make it issue a double Ctrl-C to break out of any existing code when entering the raw REPL (two Ctrl-C characters were sent in order to more reliably trigger the preemptive NLR jump). No other port has preemptive NLR jumps and so a double Ctrl-C doesn't really behave any differently to a single Ctrl-C: with USB CDC the double Ctrl-C would most likely be in the same USB packet and so processed in the same low-level USB callback, so it's just setting the keyboard interrupt flag twice in a row. The VM/runtime then just sees one keyboard interrupt and acts as though only one Ctrl-C was sent. This commit changes the double Ctrl-C to a single Ctrl-C in `pyboard.py` and `mpremote`. That keeps things as simple as they need to be. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 11:40:08 +11:00
Damien George	7746785035	tests/run-tests.py: Wait for soft reset if a target skips a test. ... Commit 69c25ea865 made raising `SystemExit` do a soft reset (on bare-metal targets). This means that any test which is skipped by a target (by raising `SystemExit`) will trigger a soft reset on that target, and then it must execute its startup code, such as `boot.py`. If the timing is right, this startup code can be unintentionally interrupted by the test runner when preparing the next test, because the test runner enters the raw REPL again via a Ctrl-C Ctrl-A ctrl-D sequence (in `Pyboard.enter_raw_repl()`). When this happens (`boot.py` is interrupted) the target may not be set up correctly, and it may (in the case of stm32 boards) flash LEDs and take extra time, slowing down the test run. Fix this by explicitly waiting for the target to finish its soft reset when it skips a test. Signed-off-by: Damien George <damien@micropython.org>	2024-10-15 11:23:07 +11:00