16509 Commits

This Branch

This Branch

All Branches

Author	SHA1	Message	Date
Damien George	bdda91fe74	tests/extmod_hardware: Add a test for machine.PWM freq and duty. ... This adds a hardware test for `machine.PWM`. It requires a jumper wire between two pins, uses `machine.PWM` to output on one of them, and `machine.time_pulse_us()` to time the PWM on the other pin (some boards test more than one pair of pins). It times both the high and low duty cycle (and hence the frequency) for a range of PWM frequencies and duty cycles (including full on and full off). Currently supported on: - esp32 (needs a minor hack for initialisation, and some tests still fail) - esp8266 (passes for frequencies 1kHz and less) - mimxrt / Teensy 4.0 (passes) - rp2 (passes) - samd21 (passes for frequencies 2kHz and less) Signed-off-by: Damien George <damien@micropython.org>	2024-12-11 12:22:15 +11:00
iabdalkader	94343e20e5	stm32/boards/STM32F429DISC: Fix SDRAM configuration. ... Define SDRAM frequency and refresh cycles. This was missed in commit 17808e7b74. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-11 12:17:40 +11:00
Angus Gratton	d4d1d4798c	esp32: Simplify thread cleanup. ... Now we only support the case of !CONFIG_FREERTOS_ENABLE_STATIC_TASK_CLEAN_UP, can simplify the cleanup code. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-12-10 23:21:46 +11:00
Angus Gratton	d90aff5e13	esp32: Remove IDF-version-specific sdkconfig. ... This reverts commit 27279e69b4 (plus removes some additional references to the SDKCONFIG_IDF_VERSION_SPECIFIC CMake variable.) Relevant sdkconfig options are added into sdkconfig.base now that IDF >=5.2.0 is required. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-12-10 23:21:46 +11:00
Angus Gratton	6e5d8d0093	esp32: Drop support for ESP-IDF below V5.2.0. ... Specifically, remove all conditional compilation for these earlier versions and change the idf_component.yml specifiers to require >=5.2.0. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-12-10 23:21:46 +11:00
Alessandro Gatti	82e382a399	esp32/mpconfigport: Use the appropriate wait-for-interrupt opcode. ... When threading is disabled, the pending events handling code would wait for an incoming interrupt once there's no more work to do. This bit of code was Xtensa-specific and wouldn't compile on a RISC-V based MCU. This commit provides the RISC-V equivalent to that part of the code, allowing to make threadless MicroPython builds on RISC-V based MCUs. Signed-off-by: Alessandro Gatti <a.gatti@frob.it>	2024-12-10 21:57:40 +11:00
Andrew Leech	9441ce6e3c	esp32: Use capability defines to configure features. ... This updates esp32 code where appropriate to replace ifdef's based on a list of specific chips with a feature SOC_* definition. This should simplify adding new esp32-* chips in future, deferring chip feature support to the IDF. Signed-off-by: Andrew Leech <andrew@alelec.net>	2024-12-10 21:47:05 +11:00
Andrew Leech	fdd606dd53	py/mkrules.mk: Use partial clone for submodules if available. ... MicroPython relies on a number of submodules for third party and chip vendor libraries. Users need to check these out before building their desired ports and Github Actions CI here needs to clone them all multiple times for every build. Many of these are getting significantly larger over time, slowing down usage and consuming more disk space. Newer versions of git have features to avoid pulling all historic / blob data which can have a significant impact of total data use. This commit uses a standard feature of git to do a partial clone, with automatic fallback to previous behavior on error. Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>	2024-12-10 17:17:17 +11:00
Alessandro Gatti	e8c3f31ba2	mimxrt/machine_rtc: Deprecate RTC.cancel in MicroPython v2. ... The current documentation for the `machine.RTC` class contains information about the `RTC.cancel` method for cancelling pending alarms. However only two ports (cc3200 and mimxrt) implement this functionality but under a different name: `RTC.alarm_cancel`. The mimxrt port also implements `RTC.cancel` but it is aliased to `RTC.alarm_cancel` anyway. To maintain naming consistency, this commit updates the documentation to officially define `RTC.alarm_cancel` as the method to call to cancel pending alarms and deprecates mimxrt's `RTC.cancel` implementation. `RTC.cancel` in the mimxrt port is thus scheduled for removal in MicroPython v2. Signed-off-by: Alessandro Gatti <a.gatti@frob.it>	2024-12-10 12:16:03 +11:00
Alessandro Gatti	28b5244666	extmod/modplatform: Distinguish RISC-V 64 from RISC-V 32. ... This commit lets the platform module report a more accurate architecture name when running on a RISC-V 64 bits platform. Signed-off-by: Alessandro Gatti <a.gatti@frob.it>	2024-12-10 12:10:36 +11:00
Alessandro Gatti	2a8f6047ff	py/emitglue: Fix clear cache builtin warning on Clang for AArch32. ... This commit fixes a warning occurring on Clang when calling `__builtin___clear_cache` with non-void pointers for its start and end memory area locations. The code now uses a char pointer for the end location, and it still builds without warnings on GCC. Signed-off-by: Alessandro Gatti <a.gatti@frob.it>	2024-12-10 12:04:14 +11:00
Alessandro Gatti	5784714f73	shared/runtime/gchelper_generic: Fix AArch32 build on Clang. ... This commit fixes a compile error happening on Clang when building the generic gchelper code for AArch32. Clang would raise a warning regarding undefined variable access when aliasing a variable to an existing CPU register. The fix is pretty crude but it works - it simply disables the warning in question for the AArch32 gchelper collection function. Care was taken to make sure the code would also compile on GCC without warnings of sorts. Signed-off-by: Alessandro Gatti <a.gatti@frob.it>	2024-12-10 12:03:34 +11:00
stijn	0f7d68043f	py/misc: Fix msvc and C++ compatibility. ... Use an explicit cast to suppress the implicit conversion which started popping up in recent compiler versions (and wasn't there yet in 07bf3179). Signed-off-by: stijn <stijn@ignitron.net>	2024-12-10 11:30:59 +11:00
Angus Gratton	31a1e2b96d	rp2: Pass V=1 or BUILD_VERBOSE to rp2 build. ... Similar to esp32. Previously rp2 could build verbose by passing VERBOSE=1, which is picked up by Makefiles generated from CMake. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-12-10 11:28:38 +11:00
Angus Gratton	160a4812cd	esp32: Pass V=1 or BUILD_VERBOSE through to idf.py when building. ... Allows verbose build to work the same on esp32 port as other ports. To minimise copy/paste, split the BUILD_VERBOSE section of mkenv.mk out to its own verbose.mk and include this in the port Makefile. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-12-10 11:28:38 +11:00
Daniël van de Giessen	5fb846df67	esp32: Fix machine_touchpad compiling on IDFv5.3. ... Signed-off-by: Damien George <damien@micropython.org>	2024-12-10 11:20:15 +11:00
Andrew Leech	5564f3042c	esp32: Add basic espressif IDF v5.3 compatibility. ... Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au> Signed-off-by: Damien George <damien@micropython.org>	2024-12-10 11:20:00 +11:00
Angus Gratton	b20687d0e7	esp32: Fix link failure due to link library order. ... When a wrapped symbol is provided in its own file, it's possible for the linker to skip that file entirely and not return to it depending on the order of libraries passed on the linker command line. This is because these wrapped symbols create linker cycles (libmain_espXX depends on liblwip but liblwip now also depends on libmain for the wrapped functions in lwip_patch.c, for example.) Linker failure for symbols in lwip_patch.c was reproducible if mDNS was disabled in the board configuration. This commit adds an explicit undefined symbol for each file, to ensure the linker will add the wrapped objects on its first pass. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-12-10 11:11:31 +11:00
iabdalkader	2bee8e1b8c	mimxrt/mpconfigport: Update FATFS config to align with other ports. ... Make this port use the same FATFS config as stm32, rp2, renesas-ra. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 11:05:05 +11:00
iabdalkader	a2cdf9a95f	renesas-ra/mpconfigport: Switch FATFS LFN to type 2. ... LFN type 2 uses the stack to allocate the internal working buffer for LFN, which is thread-safe and saves about 512 bytes of BSS memory (at the expense of needing that much memory on the stack). Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 11:04:59 +11:00
iabdalkader	309aa26811	rp2/mpconfigport: Switch FATFS LFN to type 2. ... LFN type 2 uses the stack to allocate the internal working buffer for LFN, which is thread-safe and saves about 512 bytes of BSS memory (at the expense of needing that much memory on the stack). Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 11:04:49 +11:00
iabdalkader	fd01cdd203	stm32/mpconfigport: Switch FATFS LFN to type 2. ... LFN type 2 uses the stack to allocate the internal working buffer for LFN, which is thread-safe and saves about 512 bytes of BSS memory (at the expense of needing that much memory on the stack). Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 11:02:52 +11:00
iabdalkader	89191b00ea	stm32/main: Deinitialize SPI and I2C on soft-reset. ... Following UART, CAN, Timer, etc. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:54:16 +11:00
iabdalkader	405aa69887	stm32/pyb_i2c: Add pyb_i2c_deinit_all function. ... I2C objects can remain active after a soft-reboot because they are statically allocated and lack a finalizer to collect and deinitialize them. This commit adds a `pyb_i2c_deinit_all()` function for I2C, similar to other peripherals such as UART, DAC, etc. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:53:47 +11:00
iabdalkader	d42e39d87d	stm32/spi: Add spi_deinit_all function. ... SPI objects can remain active after a soft-reboot because they are statically allocated and lack a finalizer to collect and deinitialize them. This commit adds a `spi_deinit_all()` functions for SPI, similar to other peripherals such as UART, DAC, etc. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:53:24 +11:00
iabdalkader	17808e7b74	stm32/sdram: Make SDRAM refresh count configurable by a board. ... Refresh count calculations were using a hard-coded SDRAM frequency and refresh cycles, so change them to values that can be set by a board. And set these options to their existing values on STM32F769DISC and STM32F7DISC boards. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:49:50 +11:00
iabdalkader	47d9988df2	stm32/boards: Rename SDRAM frequency config option to make units clear. ... Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:49:29 +11:00
iabdalkader	46ca78e23f	stm32/boards: Update Arduino board configs for SPI reset and bootloader. ... Update ARDUINO_GIGA, ARDUINO_OPTA, ARDUINO_NICLA_VISION and ARDUINO_PORTENTA_H7 to: - Enable SPI flash soft-reset. - Disable enter bootloader via reset. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:44:33 +11:00
iabdalkader	b5e80fafb2	drivers/memory/spiflash: Add a config option to soft-reset SPI flash. ... Add a compile-time config option to soft-reset SPI flash on init. This puts the flash in a known state on reset. Note this option is disabled by default. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:40:06 +11:00
iabdalkader	d5d366beef	nrf/boards/ARDUINO_NANO_33_BLE_SENSE: Update LED and timer config. ... Changes: - Enable hardware timer. - Define LED pins. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:37:02 +11:00
iabdalkader	67b4e6236b	mimxrt: Switch to shared TinyUSB descriptor. ... This removes duplicated TinyUSB configuration and port-specific code. Tested on RT1062, CDC+MSC still working. @robert-hh tested CDC with 1011, 1015, 1020 and 1176. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:29:21 +11:00
iabdalkader	c55202dd63	shared/tinyusb: Set MSC max endpoint size based on device speed. ... Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:26:27 +11:00
iabdalkader	a118cf9ab0	extmod/extmod.mk: Fix libmetal build prefix. ... libmetal source files already have the build directory prefix, because they're auto-generated inside the build directory. When they're added to `SRC_THIRDPARTY_C`, another build directory prefix is added resulting in the object files being generated in a nested build directory. This patch strips the build directory prefix before adding libmetal's source files. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:25:02 +11:00
Damien George	2c80d36998	tests/extmod: Convert machine1.py test to use unittest. ... Signed-off-by: Damien George <damien@micropython.org>	2024-12-06 13:48:23 +11:00
Damien George	c7c3ffa45f	tests/net_hosted: Convert connect-nonblock-xfer test to use unittest. ... This allows it to run parts of the test on esp8266 (or any target using axTLS). Signed-off-by: Damien George <damien@micropython.org>	2024-12-06 13:48:23 +11:00
Damien George	f62df1a2c2	tests/ports/stm32_hardware: Convert DMA test to use unittest. ... Signed-off-by: Damien George <damien@micropython.org>	2024-12-06 13:48:23 +11:00
Damien George	d3d2976586	qemu/Makefile: Include unittest in firmware. ... So that this port can run unittest-based tests. Signed-off-by: Damien George <damien@micropython.org>	2024-12-06 13:48:07 +11:00
Damien George	42f37e951b	esp8266/mpconfigport: Enable function attributes. ... This allows `unittest` to work on esp8266 boards. Signed-off-by: Damien George <damien@micropython.org>	2024-12-06 13:48:07 +11:00
Damien George	6dcbdec4de	lib/micropython-lib: Update submodule to latest. ... This brings in: - umqtt.simple: add optional socket timeout to connect method - aioespnow,webrepl: use recommended network.WLAN.IF_[AP|STA] constants - unittest: allow SkipTest to work within a subTest - unittest: always use "raise" with an argument Signed-off-by: Damien George <damien@micropython.org>	2024-12-06 13:48:07 +11:00
Damien George	a8422439ab	tests/run-tests.py: Print .out file when there is no .exp file. ... So that a failing unittest-based test has its entire log printed when using `run-tests.py --print-failures`. Signed-off-by: Damien George <damien@micropython.org>	2024-12-06 13:47:21 +11:00
Damien George	a2554f0957	tests/run-tests.py: Add support for tests to use unittest. ... All the existing tests require a .exp file (either manually specified or generated running the test first under CPython) that is used to check the output of running the test under MicroPython. The test passes if the output matches the expected output exactly. This has worked very well for a long time now. But some of the newer hardware tests (eg UART, SPI, PWM) don't really fit this model, for the following main reasons: - Some but not all parts of the test should be skipped on certain hardware targets. With the expected-output approach, skipping tests is either all or nothing. - It's often useful to output diagnostics as part of the test, which should not affect the result of the test (eg the diagnostics change from run to run, like timing values, or from target to target). - Sometimes a test will do a complex check and then print False/True if it passed or not, which obscures the actual test result. To improve upon this, this commit adds support to `run-tests.py` for a test to use `unittest`. It detects this by looking at the end of the output after running the test, looking for the test summary printed by `unittest` (or an error message saying `unittest` was not found). If the test uses `unittest` then it should not have a .exp file, and it's not run under CPython. A `unittest` based test passes or fails based on the summary printed by `unittest`. Note that (as long as `unittest` is installed on the target) the tests are still fully independent and you can still run them without `run-tests.py`: you just run it as usual, eg `mpremote run <test.py>`. This is very useful when creating and debugging tests. Note also that the standard test suite testing Python semantics (eg everything in `tests/basics/`) will probably never use unittest. Only more advanced tests will, and ones that are not runnable under CPython. Signed-off-by: Damien George <damien@micropython.org>	2024-12-06 13:41:52 +11:00
Amirreza Hamzavi	406bccc753	docs/library/binascii: Add docs for binascii.crc32 method. ... Signed-off-by: Amirreza Hamzavi <amirrezahamzavi2000@gmail.com>	2024-12-03 22:22:55 +11:00
chuangjinglu	2e796d6c3e	docs,ports: Fix some comments and error messages with doubled-up words. ... Signed-off-by: chuangjinglu <chuangjinglu@outlook.com>	2024-11-30 13:08:33 +11:00
Alessandro Gatti	3de3821abf	extmod/modplatform: Add Android to the recognised platforms list. ... This commit adds code to distinguish between regular Linux and Android, also adding a specific entry for the platform libc. The reported libc is marked as "bionic" and its version matches the Android platform API version (there are no definitions for a specific bionic version). Signed-off-by: Alessandro Gatti <a.gatti@frob.it>	2024-11-30 12:42:51 +11:00
Alessandro Gatti	09cf01d7c1	extmod/modplatform: Add Clang to the known compilers list. ... This commit adds support to distinguish between GCC and Clang to report the appropriate compiler version. Usually Clang also disguises itself as GCC for compatibility reasons, but these changes look for Clang-specific definitions first to avoid that problem. Signed-off-by: Alessandro Gatti <a.gatti@frob.it>	2024-11-30 12:42:51 +11:00
Alessandro Gatti	579e840de6	extmod/modplatform: Distinguish AArch64 from AArch32. ... This commit adds a new platform architecture name for Arm CPUs running in 64 bits mode ("aarch64"). The 32 bits name is left as "arm" to maintain compatibility with existing code. Signed-off-by: Alessandro Gatti <a.gatti@frob.it>	2024-11-30 12:42:51 +11:00
Angus Gratton	beabef5aac	esp32: Add missing network.STAT_CONNECT_FAIL constant. ... The esp32 port had network.STAT_ASSOC_FAIL for the same purpose, but this is undocumented and different to all other ports. That constant is now deprecated. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-11-30 12:36:03 +11:00
dependabot[bot]	6dd976cc5c	github/workflows: Bump codecov/codecov-action from 4 to 5. ... Bumps [codecov/codecov-action](https://github.com/codecov/codecov-action) from 4 to 5. - [Release notes](https://github.com/codecov/codecov-action/releases) - [Changelog](https://github.com/codecov/codecov-action/blob/main/CHANGELOG.md) - [Commits](https://github.com/codecov/codecov-action/compare/v4...v5) --- updated-dependencies: - dependency-name: codecov/codecov-action dependency-type: direct:production update-type: version-update:semver-major ... Signed-off-by: dependabot[bot] <support@github.com>	2024-11-30 12:05:16 +11:00
Angus Gratton	d49c1e836c	tools/ci.sh: Remove explicit macOS pkg-config install. ... Reasons to remove this: - GitHub's macOS runners install this package by default nowadays. - Brew renamed this package to 'pkgconf' so installing the old name on top of the new package name has started failing. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-11-30 11:24:36 +11:00
Angus Gratton	eb80b04944	tests/extmod: Workaround CPython warning in asyncio_new_event_loop test. ... This started failing in CI on the mingw build, after CPython updated to 3.12.7. The test prints two warnings during interpreter shutdown of "Task was destroyed but it is pending!". This didn't happen on other CPython builds, and I think that's because of finalizer order in CPython interpreter shutdown but not certain (the loop finalizer calls loop.close() if not already closed). Adding explicit calls to loop.close() causes the warning to be printed on every run with CPython 3.12.7 on Linux. Next, added the workaround exception handler to swallow this exception as MicroPython doesn't produce an equivalent. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-11-28 23:12:34 +11:00