To keep things neat and tidy, we ensure that each file has 1 and only 1
newline at the end of each file.
Signed-off-by: David Lechner <david@pybricks.com>
Otherwise the Python network object continues to report that it is
attempting to connect.
Also make the return error code consistent with wifi scan.
Signed-off-by: Damien George <damien@micropython.org>
This makes sure deinit() can be called on the interface many times without
error, and that the state of the driver is fully reset.
Fixes issue #7493.
Signed-off-by: Damien George <damien@micropython.org>
A board can now define the following to fully customise the extended block
device interface provided by the storage sub-system:
- MICROPY_HW_BDEV_BLOCKSIZE_EXT
- MICROPY_HW_BDEV_READBLOCKS_EXT
- MICROPY_HW_BDEV_WRITEBLOCKS_EXT
- MICROPY_HW_BDEV_ERASEBLOCKS_EXT
Signed-off-by: Damien George <damien@micropython.org>
Add a new board type for ESP32-C3 revision 3 and up that implement the USB
serial/JTAG port on pin 18 and 19. This variant uses the USB serial for
programming and console, leaving the UART free.
- Pins 18 and 19 are correctly reserved for this variant. Also pins 14-17
are reserved for flash for any ESP32-C3 so they can't be reconfigured
anymore to crash the system.
- Added usb_serial_jtag.c and .h to implement this interface.
- Interface was tested to work correctly together with webrepl.
- Interface was tested to work correctly when sending and receiving
large files with ampy.
- Disconnecting terminal or USB will not hang the system when it's
trying to print.
This makes fill() about 7x faster (PYBV11 and PYBD_SF6) for the cost of +40
bytes of bytecode (or 120 bytes text).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Flash erase/program functions disable the XIP bit. If any code runs from
flash at the same time (eg an IRQ or code it calls) it will fail and cause
a lockup.
This makes it work like --no-follow and --no-exclusive using a mutex group
and dest. Although the current implementation with BooleanOptionAction is
neater it requires Python 3.9, so don't use this feature.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The --no-exclusive flag was accidentally added to the mutex group in
178198a01d.
The --soft-reset flag was accidentally added to the mutex group in
41adf17830.
These flags can be specified independently to --[no-]follow so should not
be in that mutex group.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This achieves a substantial performance improvement when rendering glyphs
to color displays, the benefit increasing proportional to the number of
pixels in the glyph.
And using "-B" means mpy-cross is forcefully rebuilt, sometimes with
invalid CFLAGS_EXTRA options which makes the auto-build fail.
Signed-off-by: Damien George <damien@micropython.org>
This is a generic API for synchronously bit-banging data on a pin.
Initially this adds a single supported encoding, which supports controlling
WS2812 LEDs.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The sys.stdin.buffer and sys.stdout.buffer streams work just as well (and
are just as fast) as pyb.USB_VCP on stm32 devices, so there's no need to
have the USB_VCP specialisation code, which just adds complexity.
Also, on stm32 devices with both USB and UART (or other serial interface),
if something other than the USB_VCP port is used for the serial connection
then mpremote mount will not work because it will default to reading and
writing on USB_VCP instead of the other connected serial stream.
As part of this simplification, support for a second port as input is
removed (this feature was never exposed to the user).
Signed-off-by: Damien George <damien@micropython.org>
This was missed in 692d36d779. It's not
strictly necessary as the GC will clean it anyway, but it's good to
pre-emptively gc_free() all the blocks used in lexing/parsing.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Prevents the finaliser from being missed if there's a dangling reference
on the stack to one of the blocks for the files (that this test checks
that they get finalised).
See github.com/micropython/micropython/pull/7659#issuecomment-899479793
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This compiler is unable to optimise out the giant strcmp match generated
by MP_MATCH_COMPRESSED.
See github.com/micropython/micropython/pull/7659#issuecomment-899479793
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This tests both sending indications/notifications from a server to
subscribed clients via gatts_write(...,send_update=True) and subscribing
from a client.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This allows the write to trigger a notification or indication, but only to
subscribed clients. This is different to gatts_notify/gatts_indicate,
which will unconditionally notify/indicate.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This implements (most of) the PEP-498 spec for f-strings and is based on
https://github.com/micropython/micropython/pull/4998 by @klardotsh.
It is implemented in the lexer as a syntax translation to `str.format`:
f"{a}" --> "{}".format(a)
It also supports:
f"{a=}" --> "a={}".format(a)
This is done by extracting the arguments into a temporary vstr buffer,
then after the string has been tokenized, the lexer input queue is saved
and the contents of the temporary vstr buffer are injected into the lexer
instead.
There are four main limitations:
- raw f-strings (`fr` or `rf` prefixes) are not supported and will raise
`SyntaxError: raw f-strings are not supported`.
- literal concatenation of f-strings with adjacent strings will fail
"{}" f"{a}" --> "{}{}".format(a) (str.format will incorrectly use
the braces from the non-f-string)
f"{a}" f"{a}" --> "{}".format(a) "{}".format(a) (cannot concatenate)
- PEP-498 requires the full parser to understand the interpolated
argument, however because this entirely runs in the lexer it cannot
resolve nested braces in expressions like
f"{'}'}"
- The !r, !s, and !a conversions are not supported.
Includes tests and cpydiffs.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The correct callback-deregister functions must be called dependent on the
socket type, otherwise resources may not be freed correctly.
Signed-off-by: Damien George <damien@micropython.org>
Test instances can now use the following methods to synchronise their
execution:
multitest.broadcast("sync message")
multitest.wait("sync message")
Signed-off-by: Damien George <damien@micropython.org>
Anywhere a module is mentioned, use its "non-u" name for consistency.
The "import module" vs "import umodule" is something of a FAQ, and this
commit intends to help clear that up. As a first approximation MicroPython
is Python, and so imports should work the same as Python and use the same
name, to a first approximation. The u-version of a module is a detail that
can be learned later on, when the user wants to understand more and have
finer control over importing.
Existing Python code should just work, as much as it is possible to do that
within the constraints of embedded systems, and the MicroPython
documentation should match the idiomatic way to write Python code.
With universal weak links for modules (via MICROPY_MODULE_WEAK_LINKS) users
can consistently use "import foo" across all ports (with the exception of
the minimal ports). And the ability to override/extend via "foo.py"
continues to work well.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is a simple rename of the files, no content changes
(other than updating index.rst to use the new paths)
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Includes documentation for Zephyr specific modules (zephyr and zsensor),
classes (DiskAccess and FlashArea), and functions.
Signed-off-by: Julia Hathaway <julia.hathaway@nxp.com>
Includes an introduction to using the Zephyr port on MicroPython. The
quickref details examples of how to use each module the port currently
supports. The tutorial provides additional details for Zephyr specific
modules.
Signed-off-by: Julia Hathaway <julia.hathaway@nxp.com>
This commit creates a new stm32 board for the NUCLEO_H743ZI2, which is the
current version of this from ST. This is a modified copy of the
NUCLEO_H743ZI board, and the ZI2 board differs in a few minor ways:
- LED2 has moved from PB7 to PE1 and is now yellow rather than blue
- the USB power enable has moved from PG6 to PG10
- the USER button is now pulled down
This function can be used to enable and disable the DC/DC converter with or
without the Bluetooth stack enabled. It can also be used to query the
current state of the DC/DC.
This commit also adds a definition of ARRAY_SIZE needed by nrfx HAL-layer.
extmod/vfs_lfs.c needs to resolve `mp_hal_time_ns()` in order to calculate
a timestamp from 1970 epoch. A wall clock is not available in the nrf
port, hence the function is implemented to resolve compilation linkage
error. The function always return 0.
Set the default manifest to "modules/manifest.py". This includes files
from the folder "modules/scripts". The manifest default value is overriden
by all nrf51 boards that have SoftDevice present (SD=s110) to save flash.
Also add "modules/manifest.py" which is set to freeze
"modules/scripts/_mkfs.py".
Add a helper script _mkfs.py which automatically formats the file system if
nrf.Flash() is located and a VFS file system has been included in the
compilation.
The precedence is: first LFS1, LFS2 then FAT.
Update the Makefile to handle FROZEN_MANIFEST, and the README with some
small samples on how to use freeze manifests. And add BOARD_DIR to the
Makefile which can be referenced in boards/<board>/mpconfigboard.mk to
include a board specific manifest.
Enable the following features for all boards except
nrf51 boards with SoftDevice present:
- MICROPY_VFS
- MICROPY_PY_NRF
- MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE
Add posibility to override linker script "_fs_size" from make by adding the
FS_SIZE parameter. The syntax of value is linker script syntax. For
example, the value of 131072 bytes can be written as 128K like this:
FS_SIZE=128K.
If not set, default value for "_fs_size" from linker script will be used.
Disable MICROPY_FATFS_MULTI_PARTITION configuration because there is no
partition table in the flash for FATFS to read.
Also, set MICROPY_FATFS_MAX_SS to the size of a flash page. For nrf51 the
value 1024 is set. For nrf52/nrf91 the value 4096 is set.
This documents parameters that can be passed to make to enable a specific
file system to included in the build. Also, document the Makefile override
parameter "FS_SIZE" that can be used to tune the size of the flash region
to use as internal flash file system.
Update flash.c to also be compiled in when
MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE is enabled and SoftDevice is
present.
Update bluetooth/ble_drv.c to forward flash events to flash.c when
MICROPY_HW_ENABLE_INTERNAL_FLASH_STORAGE is enabled.
This commit adds the "nrf" module for port specific modules and objects.
Included in it is the "Flash" object which exposes a block device
implementation to access internal SoC flash.
Thanks to @aykevl aka Ayke van Laethem for the initial implementation.
Calculate the unused flash area on the target device. The values will be
exposed by _unused_flash_start and _unused_flash_length. The start address
and the length are not aligned to either word or pages.
This allows changing the frequency to: 100kHz, 200kHz, 400kHz, 800kHz,
1MHz, 2MHz, 4MHz, 8MHz, 16MHz, 32MHz, 64MHz. For frequencies 2MHz and
below, low power run (LPR) mode is enabled automatically.
Signed-off-by: Damien George <damien@micropython.org>
For consistency with other board-level config macros that begin with
MICROPY_HW_USB.
Also allow boards in the mimxrt, nrf and samd ports to configure these
values.
Signed-off-by: Damien George <damien@micropython.org>
Commit 4173950658 removed automatic building
of mpy-cross, which rebuilt it whenever any of its dependent source files
changed.
But needing to build mpy-cross, and not knowing how, is a frequent issue.
This commit aims to help by automatically building mpy-cross only if it
doesn't exist. For Makefiles it uses an order-only prerequisite, while
for CMake it uses a custom command.
If MICROPY_MPYCROSS (which is what makemanifest.py uses to locate the
mpy-cross executable) is defined in the environment then automatic build
will not be attempted, allowing a way to prevent this auto-build if needed.
Thanks to Trammell Hudson aka @osresearch for the original idea; see #5760.
Signed-off-by: Damien George <damien@micropython.org>
Optionally enabled via MICROPY_PY_UJSON_SEPARATORS. Enabled by default.
For dump, make sure mp_get_stream_raise is called after
mod_ujson_separators since CPython does it in this order (if both
separators and stream are invalid, separators will raise an exception
first).
Add separators argument in the docs as well.
Signed-off-by: Peter Züger <zueger.peter@icloud.com>
Signed-off-by: Damien George <damien@micropython.org>
Reverse operations are supported on stm32 and rp2, and esp32 has enough
space to also enable inplace operations, to make it complete.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This enables optional support for the hardware UART to use the RTS and/or
CTS pins for flow control.
The new "flow" constructor keyword specifies a bitmask of RTS and/or CTS.
This matches the interface used by machine.UART on stm32 and rp2.
Previously on ESP32 it was possible to specify which pins to use for the
RTS and CTS signals, but hardware flow control was never functional: CTS
was not checked before transmitting bytes, and RTS was always driven high
(signalling no buffer space available). With this patch, CTS and RTS both
operate as expected.
This also includes an update to the machine.UART documentation.
Signed-off-by: Will Sowerbutts <will@sowerbutts.com>
Commit e33bc597 ("py: Remove calls to file reader functions when these
are disabled.") changed the condition for one caller of
do_execute_raw_code() from
MICROPY_PERSISTENT_CODE_LOAD
to
MICROPY_HAS_FILE_READER && MICROPY_PERSISTENT_CODE_LOAD
The condition that enables compiling the function itself needs to be
changed to match.
Signed-off-by: David Lechner <david@pybricks.com>
Hyperflash is used by the MIMXRT1050_EVKB, MIMXRT1060_EVK and
MIMXRT1064_EVK boards.
This commit includes:
- add support for Hyperflash
- modify MIMXRT1060_EVK and MIMXRT1064_EVK to change from QSPI to
hyperflash.
- minor incidental changes to other boards so they still build
Note: Erasing a sector on the hyperflash is slow. It takes about a second,
which seems too long, but matches the data sheet.
Add basic support for LEGO HUB NO.6 (e.g. LEGO SPIKE Prime, LEGO MINDSTORMS
Robot Inventor).
See README.md for details.
Thanks to @dpgeorge for helping put this together.
Signed-off-by: Tobias Thyrrestrup <tt@LEGO.com>
It needs to use a different function because the formula to compute the
baudrate on LPUART1 is different to a normal UART.
Fixes issue #7466.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this fix, if the UART hardware FIFO had a few chars but still
below the FIFO trigger threshold, and the ringbuf was empty, the read
function would timeout if timeout==0 (the default timeout).
This fix follows the suggestion of @iabdalkader.
The RX IRQ does not trigger if the FIFO is less than the trigger level, in
which case characters may be available in the FIFO, yet not in the ringbuf,
and the ioctl returns false.
When l2cap_send detects that the sys mempool is running low (used to store
the outgoing HCI payloads), it will report stalled back to the application,
and then only unstall once these HCI payloads have been sent.
This prevents a situation where a remote receiver with very large MTU can
cause NimBLE to queue up more than MYNEWT_VAL_MSYS_1_BLOCK_COUNT (i.e. 12)
payloads, causing further attempts to send to fail with ENOMEM (even though
the channel is not stalled and we have room in the channel mbufs). The
regular credit/stall flow control is not effective here because the
receiver's MTU is large enough that it will not activate (i.e. there are
lots of credits available).
Thresholds of 1/2 (stall) and 1/4 (unstall) chosen to allow headroom for
other payloads (e.g. notifications) and that when a regular stall occurs it
might keep sending (and creating more payloads) in the background.
Previously a subclass of a type that didn't implement unary_op, or didn't
handle MP_UNARY_OP_BOOL, would raise TypeError on bool conversion.
Fixes#5677.
* Make SDRAM test cache-aware for newer MCUs.
* Use the defined data bus width (instead of the fixed 8-bits).
* Allow optional failure on error with verbose error messages.
* Test speed is now inverted (test accepts exhaustive instead fast).
This helps the OS switch to and give other threads processing time during
the sleep. It also ensures that pending events are handled, even when
sleeping for 0ms.
Fixes issue #5344.
Signed-off-by: Damien George <damien@micropython.org>
Call MICROPY_EVENT_POLL_HOOK even on very short delays so that busy loops
that call sleep_ms still yield to events and other threads.
See related issue #5344.
Replace "master" with "controller" and "slave" with "peripheral" in
comments, errors, and debug messages.
Add CONTROLLER and PERIPHERAL constants to pyb.SPI and pyb.I2C classes;
retain MASTER and SLAVE constants for backward compatiblity.
In 2ae3c890bd, -Wimplicit-fallthrough=0 was
added to get the build to pass. This option is equivalent to
-Wno-implicit-fallthrough, and the latter is compatible with clang (while
the former is not).
Fixes issue #7546.
Signed-off-by: Damien George <damien@micropython.org>
A correctly-behaved application shouldn't do this, but in the
case where the channel is stalled, there's still enough room
in the mbuf pool, then we'll fail the send (BLE_HS_EBUSY) so
the mbuf needs to be freed.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This adds #if MICROPY_PY_USELECT_SELECT around the uselect.select()
function. According to the docs, this function is only for CPython
compatibility and should not normally be used. So we can disable it
and save a few bytes of flash space where possible.
Signed-off-by: David Lechner <david@pybricks.com>
Using a 2-item transaction queue instead of 1 allows long transfers to
be executed with the minimum inter-transaction delay. Limit maximum
transaction length to ensure an integer multiple of the SPI `bits`
setting are transferred. Fixes#7511.
The MP_OBJ_STOP_ITERATION optimisation is a shortcut for creating a
StopIteration() exception object, and means that heap memory does not need
to be allocated for the exception (in cases where it can be used). This
commit allows this optimised object to take an optional argument (before,
it could only have no argument).
The commit also adds some new tests to cover corner cases with
StopIteration and generators that previously did not work.
Signed-off-by: Damien George <damien@micropython.org>
MicroPython implements some 3.5+ features, and this change helps to reduce
the need for some .exp files in the test suite.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit moves all first-party code developed for this project from lib/
to shared/, so that lib/ now only contains third-party code.
The following directories are moved as-is from lib to shared:
lib/libc -> shared/libc
lib/memzip -> shared/memzip
lib/netutils -> shared/netutils
lib/timeutils -> shared/timeutils
lib/upytesthelper -> shared/upytesthelper
All files in lib/embed/ have been moved to shared/libc/.
lib/mp-readline has been moved to shared/readline.
lib/utils has been moved to shared/runtime, with the exception of
lib/utils/printf.c which has been moved to shared/libc/printf.c.
Signed-off-by: Damien George <damien@micropython.org>
Changes are:
- update axTLS from 2.1.3 to 2.1.5
- os_port.h is now provided by the user of the library
- PLATFORM_RNG_U8 can be defined for get_random
- fix -fsanitize=undefined diagnostics
Signed-off-by: Damien George <damien@micropython.org>
To reduce the number of calls to mp_hal_stdout_tx_strn and improve the
overall throughput of printing data. This implementation is taken from
ports/stm32/mphalport.c.
Signed-off-by: Damien George <damien@micropython.org>
For some boards, even -fm dio is too fast and they require -fm dout. This
commit links to the esptool wiki about available flash modes and changes
dio to dout.
This test snuck through without proper formatting and is causing CI for
other unrelated changes to fail.
Signed-off-by: David Lechner <david@pybricks.com>
This adds the --tags argument to the git describe command that is used
to define the MICROPY_GIT_TAG macro. This makes it match non-annotated
tags. This is useful for MicroPython derivatives that don't use
annotated tags.
Signed-off-by: David Lechner <david@pybricks.com>
Adds support for hardware SPI to the zephyr port. Consistent with other
ports, such as rp2 and stm32, we only implement the SPI protocol functions
(init and transfer). Explicit sck/mosi/miso selection is not supported
and new SPI instances are initialized with default values.
This commit adds I2S protocol support for the esp32 and stm32 ports, via
a new machine.I2S class. It builds on the stm32 work of blmorris, #1361.
Features include:
- a consistent I2S API across the esp32 and stm32 ports
- I2S configurations supported:
- master transmit and master receive
- 16-bit and 32-bit sample sizes
- mono and stereo formats
- sampling frequency
- 3 modes of operation:
- blocking
- non-blocking with callback
- uasyncio
- internal ring buffer size can be tuned
- documentation for Pyboards and esp32-based boards
- tested on the following development boards:
- Pyboard D SF2W
- Pyboard V1.1
- ESP32 with SPIRAM
- ESP32
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
These warnings appear with GCC 11. Keep them as warnings but not as
compiler errors so they can be dealt with properly in the future.
Signed-off-by: Damien George <damien@micropython.org>
The ADC_FIRST_GPIO_CHANNEL and ADC_LAST_GPIO_CHANNEL macros are no longer
needed. Instead the pin_adcX table (X = 1, 2, 3) is now generated to be
the exact size needed for a given MCU, and MP_ARRAY_SIZE(pin_adcX) is used
to determine the upper bound.
This commit also allows CPU pins to be excluded from ADC configuration if
they are hidden by prefixing their name with a "-".
Signed-off-by: Damien George <damien@micropython.org>
* Modify common functions in adc.c to accept ADC handle.
* Most external channels are connected to ADC12 which is used by default.
* For ADCAll (internal channels) ADC3 is used instead.
* Issue #4435 is possibly related (at least partially fixed).
Add new API for specifying the idle level and TX carrier output level, and
new write_pulses modes of operation. Also fix wait_done documentation
which was inverted and wrong about timing.
This change allows specification of the idle level and TX carrier output
level (through changed initialisation API), and more flexible specification
of pulses for write_pulses.
This is a breaking change for the esp32.RMT constructor API. Previous code
of this form:
esp32.RMT(..., carrier_duty_percent=D, carrier_freq=F)
will now raise an exception and should be changed to:
esp32.RMT(..., tx_carrier=(F, D, 1))
The firmware for Teensy 4.0, Teensy 4.1 and MIMXRT1020_EVK are created.
Users of other MIMXRT10xx_EVK boards should be able to build the firmware
themselves, they might need specific DEBUG settings.
The Makefile had to be changed in order to build the .bin file as well.
This adds a call to mp_deinit() in the main function of the STM32 port.
This enables the use of MICROPY_PORT_DEINIT_FUNC on that port, as well as
cleaning up the GIL if threading is enabled.
Previous behaviour was: if boot.py had an exception then main.py would
still run, which is arguably unexpected behaviour.
This commit changes the behaviour so main.py is not run if boot.py has an
error.
Signed-off-by: Damien George <damien@micropython.org>
Currently when using uasyncio.start_server() the socket configuration is
done inside a uasyncio.create_task() background function. If the address
and port are already in use however this throws an OSError which cannot be
cleanly caught behind the create_task().
This commit moves the getaddrinfo and socket binding to the start_server()
function, and only creates the task if that succeeds. This means that any
OSError from the initial socket configuration is propagated directly up the
call stack, compatible with CPython behaviour.
See #7444.
Signed-off-by: Damien George <damien@micropython.org>
This avoids the irritation of the PJRC HalfKay loader on Teensy 4.0. Block
0 and 1 are properly erased and the additional formatting in the make
script is not required anymore.
This class supports SPI bus controller mode, with blocking transfers.
SPI device numbers start at 0, to comply with the pinout of the Teensy
boards. With the configured clock frequency the fastest baud rate is
33MHz. For messages longer 16 bytes DMA is used. The class uses the
existing framework with extmod/machine_spi.c.
Extended driver options:
- drive=n with n being between 1 and 6 or PIN.POWER_1 to PIN.POWER_6.
Since the pins used by the SPI are fixed, no Pin settings can be made.
Thus the drive option is added allowing to control ringing and crosstalk
on the connection.
- gap_ns=nnnnn is the time between sent data items in a frame given in ns.
Default is 2 clock cycles.
Coverage calculated by Codecov has the same reliability/deterministic
issues as Coveralls did, so the problem is likely to do with the output of
lcov/gcov, rather than the analysis and display of the data.
Switch from lcov to gcov for data generation to try and simplify this
process of computing coverage.
Signed-off-by: Damien George <damien@micropython.org>
As discussed in #7455, Coveralls doesn't work properly anymore, it has
many spurious errors with reduced coverage.
Signed-off-by: Damien George <damien@micropython.org>
When looping, now disable the TX interrupt after calling rmt_write_items()
function to handle change in IDF behaviour (since v4.1). Also check length
of pulses to ensure it fits hardware limit.
Fixes issue #7403.
The GC now works correctly using asyncify and the functions
emscripten_scan_stack() and emscripten_scan_registers(). Stack/call depth
is monitored via the use of the pystack option.
Fixes issue #6738.
Signed-off-by: Damien George <damien@micropython.org>
Only include .c and .cpp files explicitly in the list of files passed to
the preprocessor for QSTR extraction. All relevant .h files will be
included in this process by "#include" from the .c(pp) files. In
particular for moduledefs.h, this is included by py/objmodule.c (and
doesn't actually contain any extractable MP_QSTR_xxx, but rather defines
macros with MP_QSTR_xxx's in them which are then part of py/objmodule.c).
The main reason for this change is to simplify the preprocessing step on
the javascript port, which tries to compile .h files as C++ precompiled
headers if they are passed with -E to clang.
Signed-off-by: Damien George <damien@micropython.org>
`mpy-cross` can be compiled to WASM using Emscripten, but it is not happy
unless the stack check is disabled.
Signed-off-by: David Lechner <david@pybricks.com>
Calculating the weekday each time you want to set a date is error prone and
tiresome. MicroPython can do it on its own - hardware on some ports do not
support storing weekday in hardware and always computes it on the fly,
ignoring the value given to the constructor.
During discussion for #7432 the conclusion was that there seems to be no
obvious reason to let user set the weekday to an incorrect value so it
makes sense to just ignore the provided weekday value and always compute
the correct value. This patch introduces this change for the rp2 port.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
The RTC in rp2 can store any, even wrong, number as a weekday in RTC. It
was, however, discussed in #7394 that we would like to unify all ports and
use 0 as Monday, not Sunday in the machine.RTC implementation.
This patch makes sure that the default date set in RTC is adheres to this
convention. It also fixes the example in quickref to use proper weekday to
avoid confusion.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Add an optional 'lock' kwarg to callback that locks GC and scheduler. This
allows the callback to be invoked asynchronously in 'interrupt context',
for example as a signal handler.
Also add the 'cfun' member function to callback, that allows retrieving the
C callback function address. This is needed when the callback should be
set to a struct field.
See related #7373.
Signed-off-by: Amir Gonnen <amirgonnen@gmail.com>
Fixes the following (the line numbers match commit 0e87459e2b):
../../extmod/crypto-algorithms/sha256.c:49:19: runtime error: left shif...
../../extmod/moduasyncio.c:106:35: runtime error: member access within ...
../../py/binary.c:210:13: runtime error: left shift of negative value -...
../../py/mpz.c:744:16: runtime error: negation of -9223372036854775808 ...
../../py/objint.c:109:22: runtime error: left shift of 1 by 31 places c...
../../py/objint_mpz.c:374:9: runtime error: left shift of 4611686018427...
../../py/objint_mpz.c:374:9: runtime error: left shift of negative valu...
../../py/parsenum.c:106:14: runtime error: left shift of 46116860184273...
../../py/runtime.c:395:33: runtime error: left shift of negative value ...
../../py/showbc.c:177:28: runtime error: left shift of negative value -...
../../py/vm.c:321:36: runtime error: left shift of negative value -1```
Testing was done on an amd64 Debian Buster system using gcc-8.3 and these
settings:
CFLAGS += -g3 -Og -fsanitize=undefined
LDFLAGS += -fsanitize=undefined
The introduced TASK_PAIRHEAP macro's conditional (x ? &x->i : NULL)
assembles (under amd64 gcc 8.3 -Os) to the same as &x->i, since i is the
initial field of the struct. However, for the purposes of undefined
behavior analysis the conditional is needed.
Signed-off-by: Jeff Epler <jepler@gmail.com>
It reschedules the BT HCI poll soft timer so that it is called exactly when
the next timer expires.
Signed-off-by: Damien George <damien@micropython.org>
Instead of using systick the BT subsystem is now scheduled using a soft
timer. This means it is scheduled only when it is enabled.
Signed-off-by: Damien George <damien@micropython.org>
And call mp_pairheap_init_node() in soft_timer_static_init() so that
reinsert can be called after static_init.
Signed-off-by: Damien George <damien@micropython.org>
This is to provide a summary of the licenses used by MicroPython.
- Add SPDX identifier for every directory that includes
non-MIT-licensed content.
- Add brief summary.
- Update docs license to be more explicit.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Dynamically generate/loaded native code (eg from @micropython.native or
native .mpy files) needs to be able allocate from IRAM, and the memory
protection feature must be disabled for that to work. Disabling it is
needed to get native code working on ESP32-S2 and -C3.
Signed-off-by: Damien George <damien@micropython.org>
This introduces a new macro to get the main thread and uses it to ensure
that asynchronous exceptions such as KeyboardInterrupt (CTRL+C) are only
scheduled on the main thread. This is more deterministic than being
scheduled on a random thread and is more in line with CPython that only
allow signal handlers to run on the main thread.
Fixes issue #7026.
Signed-off-by: David Lechner <david@pybricks.com>
This moves mp_pending_exception from mp_state_vm_t to mp_state_thread_t.
This allows exceptions to be scheduled on a specific thread.
Signed-off-by: David Lechner <david@pybricks.com>
2.5 can be represented correctly in object representation C, but 2.3 cannot
(it is slightly truncated).
Signed-off-by: Damien George <damien@micropython.org>
Commit 0abf6f830c removed _boot.py from the
manifest for the GENERIC_512K board because the build does not include a
filesystem. But the main code expects _boot.py to be there and prints an
error if it's not. So add a custom _boot.py, which just sets the
gc.threshold().
Signed-off-by: Damien George <damien@micropython.org>
The 72x40 OLED requires selecting the internal IREF, as opposed to the
default external IREF. This is an undocumented feature in the SSD1306
datasheet, but is present in the SSD1315 datasheet. It's possible the
72x40 OLED is actually using the newer SSD1315 controller. Sending the
IREF select command to SSD1306 displays has no effect on them, so it's
added to the init_display() instead of wrapping in an "if width = 72".
Also tested on a 128x64 OLED using the SSD1315 controller (smaller ribbon
cable) and the proposed change has no effect on the display, as the module
comes with the correct current limiting resistor. Internal and external
IREF work the same.
Fixes issue #7281.
This adds a wlan.config(reconnects=N) option to set the number of reconnect
attempts that will be made if the WLAN connection goes down. The default
is N=-1 (infinite retries, current behavior). Setting
wlan.config(reconnects=0) will disable the reconnect attempts.
A nice side effect of reconnects=0 is that wlan.status() will report the
disconnect reason now. See related issue #5326.
Ethernet-PHYs from ESP-IDF (LAN8720, IP101, RTL8201, DP83848) are now
supported in IDF v4.1 and above. PHY_KSZ8041 is only for ESP-IDF 4.3 and
above. ESP32S2 is not supported.
Signed-off-by: Tobias Eydam <eydam-prototyping@outlook.com>
The comments in NimBLE for ble_gattc_notify_custom() state that "This
function consumes the supplied mbuf regardless of the outcome.". And
inspection of NimBLE code shows that this is the case. So the comment can
be removed.
Signed-off-by: Damien George <damien@micropython.org>
This commit fixes a problem with a race between cancellation of task A and
completion of task B, when A waits on B. If task B completes just before
task A is cancelled then the cancellation of A does not work. Instead,
the CancelledError meant to cancel A gets passed through to B (that's
expected behaviour) but B handles it as a "Task exception wasn't retrieved"
scenario, printing out such a message (this is because finished tasks point
their "coro" attribute to themselves to indicate they are done, and
implement the throw() method, but that method inadvertently catches the
CancelledError). The correct behaviour is for B to bounce that
CancelledError back out.
This bug is mainly seen when wait_for() is used, and in that context the
symptoms are:
- occurs when using wait_for(T, S), if the task T being waited on finishes
at exactly the same time as the wait-for timeout S expires
- task T will have run to completion
- the "Task exception wasn't retrieved message" is printed with
"<class 'CancelledError'>" as the error (ie no traceback)
- the wait_for(T, S) call never returns (it's never put back on the
uasyncio run queue) and all tasks waiting on this are blocked forever
from running
- uasyncio otherwise continues to function and other tasks continue to be
scheduled as normal
The fix here reworks the "waiting" attribute of Task to be called "state"
and uses it to indicate whether a task is: running and not awaited on,
running and awaited on, finished and not awaited on, or finished and
awaited on. This means the task does not need to point "coro" to itself to
indicate finished, and also allows removal of the throw() method.
A benefit of this is that "Task exception wasn't retrieved" messages can go
back to being able to print the name of the coroutine function.
Fixes issue #7386.
Signed-off-by: Damien George <damien@micropython.org>
The implementation uses the LPUARTx devices. Up to 8 UARTs can be used,
given that the pins are accessible. E.g. 8 on Teensy 4.1, 5 on
MIMXRT1020_EVK.
For Tennsy 4.0 and 4.1 the UART numbers are as printed on the pinout 1..N.
The MIMXRT10xx-EVK boards have only one UART named, which gets the number
1. All other UART are assigned to different Pins:
MIMXRT1010-EVK:
D0/D1 UART 1
D6/D7 UART 2
A0/D4 UART 3
MIMXRT1020-EVK:
D0/D1 UART 1
D6/D9 UART 2
D10/D12 UART 3
D14/D15 UART 4
A0/A1 UART 5
MIMXRT1050-EVK, MIMXRT1060-EVK, MIMXRT1064-EVK:
D0/D1 UART 1
D7/D6 UART 2
D8/D9 UART 3
A1/A0 UART 4
Now a ctrl-C will not stop mpremote, rather this character will be passed
through to the attached device.
The mpremote version is also increased to 0.0.5.
Signed-off-by: Damien George <damien@micropython.org>
Using just the list of available ports, instead of a hard-coded list of
possible ports, means that all ports will be available for auto connection.
And the order that they will be attempted in will match what's printed by
"mpremote connect list" (and will be the same as before, trying ACMx before
USBx). Auto-connect will also now work on Mac, and will allow all COM
ports on Windows.
Signed-off-by: Damien George <damien@micropython.org>
With docs and a multi-test using TCP server/client.
This method is a MicroPython extension, although there is discussion of
adding it to CPython: https://bugs.python.org/issue41305
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
This fixes error: cast to smaller integer type 'int' from 'pthread_t'.
pthread_t is defined as long, not as int.
Signed-off-by: Pavol Rusnak <pavol@rusnak.io>
The rtc_set_datetime() from pico-sdk will validate the values in the
datetime_t structure and refuse to set the time if they aren't valid. It
makes sense to raise an exception if this happens instead of failing
silently which might be confusing (as an example, see:
https://github.com/micropython/micropython/pull/6928#issuecomment-860166044
).
The supplied value for microseconds in datetime() will be treated as a
starting value for the reported microseconds. Due to internal processing
in setting the time, there is an offset about 1 ms.
This change moves the datetime tuple format back to the one used by all the
other ports:
(year, month, day, weekday, hour, minute, second, microsecond)
Weekday is a number between 0 and 6, with 0 assigned to Monday. It has to
be provided when setting the RTC with datetime(), but will be ignored on
entry and calculated when needed.
The weekday() method was removed, since that is now again a part of the
datetime tuple.
The now() method was updated so it continues to return a tuple that matches
CPython's datetime module.
Initial support for machine.RTC on rp2 port. It only supports datetime()
method and nothing else. The method gets/returns a tuple of 8 items, just
like esp32 port, for example, but the usec parameter is ignored as the RP2
RTC only works up to seconds precision.
The Pico RTC isn't very useful as the time is lost during reset and there
seems to be no way to easily power up just the RTC clock with a low current
voltage, but still there seems to be use-cases for that, see issues #6831,
and a Thonny issue #1592. It was also requested for inclusion on v1.15
roadmap on #6832.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Changes introduced are:
- the application offset is now loaded from the partition table instead of
being hard-coded to 0x10000
- maximum size of all sections is computed using the partition table
- an error is generated if any section overflows its allocated space
- remaining bytes are printed for each section
Signed-off-by: Damien George <damien@micropython.org>
This commit adds a few math functions to the source list in the Makefile,
and implements the log2f function, so that ulab can be compiled on the nrf
boards. It also addresses part of #5162.
This fix prevents server.wait_closed() from raising an AttributeError when
trying to access server.task. This can happen if it is called immediately
after start_server().
This commit fixes the following problems converting to/from Python integers
and ffi types:
- integers of 8 and 16 bits not working on big endian
- integers of 64 bits not working on 32 bits architectures
- unsigned returns were converted to signed Python integers
Fixes issue #7269.
Currently only advertising and scanning are supported, using the ring
buffer for events (ie not synchronous events at this stage).
The ble_gap_advertise.py multi-test passes (tested on a nucleo_wb55rg
board).
Signed-off-by: Damien George <damien@micropython.org>
Zephyr's default value for CONFIG_NET_SOCKETS_POSIX_NAMES was changed
from false to true between Zephyr v2.5.0 and v2.6.0. This caused
conflicts in MicroPython, which uses the zsock_ prefixed functions, so
disable it.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Zephyr's Kconfig symbols and defaults for SDHC/SDMMC disk drivers and
the disk access subsystem were reworked between Zephyr v2.5.0 and
v2.6.0. Update MicroPython accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Following on from ef16834887, this adds a
coverage build and running of the test suite on an ARM 32-bit Linux-based
architecture.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this commit, cache flushing for ARM native code was done only in
the assembler code asm_thumb_end_pass()/asm_arm_end_pass(), at the last
pass of the assembler. But this misses flushing the cache when loading
native code from an .mpy file, ie in persistentcode.c.
The change here makes sure the cache is always flushed/cleaned/invalidated
when assigning native code on ARM architectures.
This problem was found running tests/micropython/import_mpy_native_gc.py on
the mimxrt port.
Signed-off-by: Damien George <damien@micropython.org>
Initial version, using the LP RTC clock. It provides setting the date and
time with rtc.init() or rtc.datetime(), and reading the date and time with
rtc.datetime() or rtc.now(). The method weekday() reports the weekday of
the current date. It starts with 0 for Monday.
The tuple order for datetime() and now() matches the CPython sequence:
(year, month, day, hour, minute, second, microsecond, TZ). TZ is ignored
and reported as None. Microsecond is provided at a best effort.
If a battery is not supplied, the default boot date/time is 1970/1/1 0:0:0.
With a battery, the clock continues to run even when the board is not
powered. The clock is quite precise. If not, using rtc.calibration() may
help.
It supports three hardware timer channels based on the PIT timers of the
MIMXRT MCU. The timer id's are 0, 1 and 2. On soft reboot all active
timers will be stopped via finalisers.
This is required since the Teensy Halfkay loader attempts to erase all of
the flash but fails to do so, at least in my tests. Formatting brings it
back to a known state.
This commit adds full support for a filesystem on all boards, with a block
device object mimxrt.Flash() and uos.VfsLfs2 enabled.
Main changes are:
- Refactoring of linker scripts to accomodate reserved area for VFS. VFS
will take up most of the available flash. 1M is reserved for code. 9K is
reserved for flash configuration, interrupts, etc.
- Addition of _boot.py with filesystem init code, called from main.c.
- Definition of the mimxrt module with a Flash class in modmimxrt.[ch].
- Implementation of a flash driver class in mimxrt_flash.c. All flashing
related functions are stored in ITCM RAM.
- Addition of the uos module with filesystem functions.
- Implementation of uos.urandom() for the sake of completeness of the uos
module.
It uses sample code from CircuitPython supplied under MIT license, which
uses the NXP SDK example code.
Done in collaboration with Philipp Ebensberger aka @alphaFred who
contributed the essential part to enable writing to flash while code is
executing, among other things.
Adds support for NeoPixels on GPIO32 and GPIO33 on ESP32. Otherwise,
NeoPixels wired to GPIO32/33 wll silently fail without any hints to the
user.
With thanks to @robert-hh.
Fixes issue #7221.
ATOM is a very small ESP32 development board produced by M5Stack, with a
size of 24mm * 24mm, with peripherals such as WS2812, IR, button, MPU6886
(Only Matrix), and 8 GPIO extensions. It also has a plastic shell.
The random module's getrandbits() method didn't give a proper error message
when calling it with a value that was outside of the range of 1-32, which
can lead to confusion using this function (which under CPython can accept
numbers larger than 32). Now instead of simply giving a ValueError it
gives an error message that states that the number of bits is constrained.
Also, since the random module's functions getrandbits() and randint()
differ from CPython, tests have been added to describe these differences.
For getrandbits the relevant documentation is shown and added to the docs.
The same is given for randint method so that the information is more easily
found.
Finally, since the int object lacks the bit_length() method there is a test
for that method also to include within the docs, showing the difference to
CPython.
asan considers that memcmp(p, q, N) is permitted to access N bytes at each
of p and q, even for values of p and q that have a difference earlier.
Accessing additional values is frequently done in practice, reading 4 or
more bytes from each input at a time for efficiency, so when completing
"non_exist<TAB>" in the repl, this causes a diagnostic:
==16938==ERROR: AddressSanitizer: global-buffer-overflow on
address 0x555555cd8dc8 at pc 0x7ffff726457b bp 0x7fffffffda20 sp 0x7fff
READ of size 9 at 0x555555cd8dc8 thread T0
#0 0x7ffff726457a (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xb857a)
#1 0x555555b0e82a in mp_repl_autocomplete ../../py/repl.c:301
#2 0x555555c89585 in readline_process_char ../../lib/mp-readline/re
#3 0x555555c8ac6e in readline ../../lib/mp-readline/readline.c:513
#4 0x555555b8dcbd in do_repl /home/jepler/src/micropython/ports/uni
#5 0x555555b90859 in main_ /home/jepler/src/micropython/ports/unix/
#6 0x555555b90a3a in main /home/jepler/src/micropython/ports/unix/m
#7 0x7ffff619a09a in __libc_start_main ../csu/libc-start.c:308
#8 0x55555595fd69 in _start (/home/jepler/src/micropython/ports/uni
0x555555cd8dc8 is located 0 bytes to the right of global variable
'import_str' defined in '../../py/repl.c:285:23' (0x555555cd8dc0) of
size 8
'import_str' is ascii string 'import '
Signed-off-by: Jeff Epler <jepler@gmail.com>
With GCC 11 there is now a warning about array bounds of OTP-mac, due to
the OTP being a literal address.
Signed-off-by: Damien George <damien@micropython.org>
If digest is called then the hash object is put in a "final" state and
calling update() or digest() again will raise a ValueError (instead of
silently producing the wrong result).
See issue #4119.
Signed-off-by: Damien George <damien@micropython.org>
The 512k build does not have a filesystem so there is no reason to include
the filesystem-related modules. This commit provides a custom manifest.py
for this board which no longer includes: _boot.py, flashbdev.py,
inisetup.py, upip.py, upip_utarfile.py. This cuts the build down by about
9k of flash.
Signed-off-by: Damien George <damien@micropython.org>
This adds a coverage build and running of the test suite on a MIPS 32-bit
big endian architecture. It uses the feature of qemu to execute foreign
code as though it were native to the system (using qemu user mode). The
code compiled for MIPS will run under the qemu VM, but all syscalls made by
this code go to the host (Linux) system.
See related #7268 and #7273.
Signed-off-by: Damien George <damien@micropython.org>
- modified pin type from pin_obj_t to machine_pin_obj_t
- created machine_pin.c
- implemented basic version of make-pins.py to genertate pins.c/.h files
automatically; the only alternate function currently supported is GPIO
- added af.csv files for all supported MCUs
- replaced pins.c/pins.h files with pin.csv for all boards
- implemented on/off/high/low/value/init methods
- Implemented IN/OUT/OPEN_DRAIN modes
- modified LDFLAGS for DEBUG build to get usefull .elf file for debugging
Signed-off-by: Philipp Ebensberger
As the new default behaviour, this allows PyDFU to be used with all
devices, not just the ones matching a specific set of VID/PID values. But
it's still possible to specify VID/PID if needed to narrow down the
selection of the USB device.
Signed-off-by: Tobias Thyrrestrup <tt@LEGO.com>
Leaving the bootloader from an IRQ (eg USB or I2C IRQ) will not work if
MBOOT_LEAVE_BOOTLOADER_VIA_RESET is disabled, ie if mboot jumps directly to
the application. This is because the CPU will still be in IRQ state when
the application starts and IRQs of lower priority will be blocked.
Fix this by setting a flag when the bootloader should finish, and exit the
bootloader always from the main (top level) thread.
This also improves the USB behaviour of mboot: it no longer abruptly
disconnects when the manifest command is sent.
Signed-off-by: Damien George <damien@micropython.org>
RX and CTS are the input pins and pull-ups are enabled so they don't cause
a problem if left unconnected. But the output pins don't need a pull up
(they were originally all configured with pull up in commit
8f7491a109).
If needed, the pull-ups can be disabled in Python using machine.Pin after
the UART is constructed.
See issue #4369.
Signed-off-by: Damien George <damien@micropython.org>
The DMA driver will turn off DMA if it hasn't been used for an amount of
time (to save power). The SDIO driver for cyw43 WLAN was not informing the
DMA driver that it was using DMA and there was a chance that the DMA would
turn off in the middle of an SDIO DMA transfer. The symptoms of this would
be printing of SDIO error messages and a failure to communicate with the
cyw43 WLAN module.
This commit fixes this issue by changing the SDIO driver to use the
dma_nohal_XXX API to initialise and start the DMA.
Signed-off-by: Damien George <damien@micropython.org>
SysTick cannot wake the CPU from WFI/WFE so a hardware timer is needed to
keep track of ticks/delay (similar to the nrf port).
Fixes issue #7234.
Signed-off-by: Damien George <damien@micropython.org>
The proper way to do this is to test for __APPLE__ and __MACH__, where
__APPLE__ tests for an Apple OS and __MACH__ tests that it is based on CMU
Mach. Using both tests ensures that just Darwin (Apple's open source base
for MacOS, iOS, etc.) is recognized. __APPLE__ by itself will test for any
Apple OS, which can include older OS 7-9 and any future Apple OS. __MACH__
tests for any OS based on CMU Mach, including Darwin and GNU Hurd.
Fixes#7232.
MicroPython does not store any reference from a function object to the
module it was defined in, but there is a way to use function.__globals__ to
indirectly get the module.
See issue #7259.
Signed-off-by: Damien George <damien@micropython.org>
This significantly reduces the time taken to run the test suite (on the
unix port). Use `-j1` to disable this feature.
Signed-off-by: Jeff Epler <jepler@gmail.com>
Array equality is defined as each element being equal but to keep
code size down MicroPython implements a binary comparison. This
can only be used correctly for elements with the same binary layout
though so turn it into an NotImplementedError when comparing types
for which the binary comparison yielded incorrect results: types
with different sizes, and floating point numbers because nan != nan.
A board can now customise mboot with:
- MBOOT_LED1, MBOOT_LED2, MBOOT_LED3, MBOOT_LED4: if it needs to have
different LEDs for mboot compared to the application
- MBOOT_BOARD_LED_INIT: if it needs a fully customised LED init function
- MBOOT_BOARD_LED_STATE: if it needs a fully customised LED state-setting
function
- MBOOT_BOARD_GET_RESET_MODE: if it needs a fully customised function to
get the reset mode
With full customisation, the only requirement is a single LED to show the
status of the bootloader (idle, erasing, flashing, etc), which can be
configured to do nothing if needed.
Signed-off-by: Damien George <damien@micropython.org>
It is enabled by default to get the standard behaviour of doing a reset
after it is finished, but can be disabled by a board to jump straight to
the application (likely the board needs to use MBOOT_BOARD_CLEANUP to make
this work).
The application is passed a reset mode of BOARDCTRL_RESET_MODE_BOOTLOADER
if the bootloader was active and entered via a jump.
Signed-off-by: Damien George <damien@micropython.org>
This new logic is equivalent to the old logic when the only possibilities
for reset_mode are NORMAL, SAFE_MODE and FILESYSTEM, which is the standard
case. But the new logic also allows other reset_mode values (eg
BOOTLOADER) to run boot.py and main.py.
Signed-off-by: Damien George <damien@micropython.org>
When disabled the bootloader is entered via a direct jump. When enabled
the bootloader is entered via a system reset then a jump. It's enabled by
default to retain the existing behaviour, which is the recommended way.
Signed-off-by: Damien George <damien@micropython.org>
Improvements made:
- PSRAM support for S2
- partition definition for 16MiB flash
- correct ADC and DAC pins
- correct GPIO and IRQ pins
- S3 components in CMakeLists
Based on original commit made by Seon Rozenblum aka @UnexpectedMaker.
Signed-off-by: Damien George <damien@micropython.org>
The RP2040 has 2 cores and supports running at most 2 Python threads (the
main one plus another), and will raise OSError if a thread cannot be
created because core1 is already in use. This commit adjusts some thread
tests to be robust against such OSError's. These tests now pass on rp2
boards.
Signed-off-by: Damien George <damien@micropython.org>
This commit makes gc_lock_depth have one counter per thread, instead of one
global counter. This makes threads properly independent with respect to
the GC, in particular threads can now independently lock the GC for
themselves without locking it for other threads. It also means a given
thread can run a hard IRQ without temporarily locking the GC for all other
threads and potentially making them have MemoryError exceptions at random
locations (this really only occurs on MCUs with multiple cores and no GIL,
eg on the rp2 port).
The commit also removes protection of the GC lock/unlock functions, which
is no longer needed when the counter is per thread (and this also fixes the
cas where a hard IRQ calling gc_lock() may stall waiting for the mutex).
It also puts the check for `gc_lock_depth > 0` outside the GC mutex in
gc_alloc, gc_realloc and gc_free, to potentially prevent a hard IRQ from
waiting on a mutex if it does attempt to allocate heap memory (and putting
the check outside the GC mutex is now safe now that there is a
gc_lock_depth per thread).
Signed-off-by: Damien George <damien@micropython.org>
Any code running on core1 should be stopped on soft-reset (the GC heap is
reset so if code continues to run on core1 it will see corrupt memory).
Signed-off-by: Damien George <damien@micropython.org>
So a lock can be acquired on one Python thread and then released on
another. A test for this is added.
Signed-off-by: Damien George <damien@micropython.org>
Because vPortCleanUpTCB runs on the FreeRTOS idle task and cannot execute
any VM or runtime related code like freeing memory.
Signed-off-by: Damien George <damien@micropython.org>
All the method signatures from rp2_pio.c and friends have been taken and
converted to RST format, then explanatory notes added for each signature.
Signed-off-by: Tim Radvan <tim@tjvr.org>
uctypes.FLOAT32 has a special value representation and
uctypes_struct_scalar_size() should be used instead of GET_SCALAR_SIZE().
Signed-off-by: Damien George <damien@micropython.org>
This fixes a bug where double arguments on a 32-bit architecture would not
be passed correctly because they only had 4 bytes of storage (not 8). It
also fixes a compiler warning/error in return_ffi_value on certian
architectures: array subscript 'double[0]' is partly outside array bounds
of 'ffi_arg[1]' {aka 'long unsigned int[1]'}.
Fixes issue #7064.
Signed-off-by: Damien George <damien@micropython.org>
This adds to the ESP8266 tutorial instructions explaining which pins to
pull low to enter programming mode.
Commit made originally by @ARF1 in #2910.
Signed-off-by: Damien George <damien@micropython.org>
The number shown in the USB id is now the same as that returned by
machine.unique_id(). All 8 bytes are inserted as hex into the USB id. A
usb id at /dev/serial/by-id then looks like:
usb-MicroPython_Board_in_FS_mode_e469b03567342f37-if00
Doing "import <tab>" will now complete/list built-in modules.
Originally at adafruit#4548 and adafruit#4608
Signed-off-by: Artyom Skrobov <tyomitch@gmail.com>
Anything beginning with "_" will now only be tab-completed if there is
already a partial match for such an entry. In other words, entering
foo.<tab> will no longer complete/list anything beginning with "_".
Originally at adafruit#1850
Signed-off-by: Kathryn Lingel <kathryn@lingel.net>
This adds an initial specification of the machine.PWM class, to provide a
way to generate PWM output that is portable across the different ports.
Such functionality may already be available in one way or another (eg
through a Timer object), but because configuring PWM via a Timer is very
port-specific, and because it's a common thing to do, it's beneficial to
have a top-level construct for it.
The specification in this commit aims to provide core functionality in a
minimal way. It also somewhat matches most existing ad-hoc implementations
of machine.PWM.
See discussion in #2283 and #4237.
Signed-off-by: Damien George <damien@micropython.org>
These commented-out lines of code have been unused for a long time, so
remove them to avoid confusion as to why they are there.
mp_obj_dict_free() never existed, this line was converted from
mp_map_deinit() and commented out as soon as it was added. The call to
mp_map_deinit(mp_loaded_modules_map) was commented in
1a1d11fa32.
Fixes issue #3507.
Signed-off-by: Damien George <damien@micropython.org>
It's now possible to specify a device serial port using shorcuts like:
$ ./run-multitests.py -i pyb:a0 -i pyb:u1 multi_bluetooth/*.py
Signed-off-by: Damien George <damien@micropython.org>
This board does not work with CONFIG_NETWORKING enabled. And
CONFIG_CONSOLE_SUBSYS is enabled so that ctrl-C works.
Signed-off-by: Damien George <damien@micropython.org>
And ctrl-C can now interrupt a time.sleep call. This uses Zephyr's k_poll
API to wait efficiently for an event signal, and an optional semaphore.
Signed-off-by: Damien George <damien@micropython.org>
This helper is added to properly set a pending exception, to mirror
mp_sched_schedule(), which schedules a function.
Signed-off-by: Damien George <damien@micropython.org>
If MICROPY_ENABLE_SCHEDULER is enabled then MP_STATE_VM(sched_state) must
be updated after handling the pending exception, which is done by the
mp_handle_pending() function.
Signed-off-by: Damien George <damien@micropython.org>
If MICROPY_ENABLE_SCHEDULER is enabled then MP_STATE_VM(sched_state) must
be updated after handling the pending exception, which is done by the
mp_handle_pending() function.
Signed-off-by: Damien George <damien@micropython.org>
This can now be selected by setting MICROPY_HW_SDIO_SDMMC, which defaults
to 1, ie SDMMC1. The pins can also be selected and default to the standard
C8/C9/C10/C11/C12/D2.
This can now be selected by setting MICROPY_HW_SDCARD_SDMMC, which defaults
to 1, ie SDMMC1. This commit also renames the SD pin configuration macros
from MICROPY_HW_SDMMC2_xxx to MICROPY_HW_SDCARD_xxx, as well as renaming
MICROPY_HW_SDMMC_BUS_WIDTH to MICROPY_HW_SDCARD_BUS_WIDTH.
Signed-off-by: Damien George <damien@micropython.org>
A board can now define MBOOT_TEXT0_ADDR to place mboot at a location other
than 0x08000000. This can be useful if, for example, there is already a
different bootloader on the device.
Signed-off-by: Damien George <damien@micropython.org>
A board can now define MBOOT_LD_FILES (at the Makefile-level) to specify
custom linker scripts. And stm32_generic.ld has been split into 2 pieces
so one or the other can be reused (usually stm32_sections.ld wolud be
reused by a board, and stm32_memory.ld redefined).
Signed-off-by: Damien George <damien@micropython.org>
A board can now use BUILDING_MBOOT at the Makefile-level to do things
conditional on building mboot, for example add source files to SRC_C.
Signed-off-by: Damien George <damien@micropython.org>
Commit 1e297c8898 introduced a bug where the
very first reset-mode state on the LEDs was not shown, because prior to
that commit the first reset-mode state was the same as the initial LED
state (green on, others off) and update_reset_mode() was called after
setting this initial LED state.
This is fixed in this commit by changing the update_reset_mode() loop so
that it displays the current reset mode before doing the delay.
Signed-off-by: Damien George <damien@micropython.org>
And use the same boardctrl.h header for both the application and mboot so
these constants are consistent.
Signed-off-by: Damien George <damien@micropython.org>
This adds support for making static (ie not on the Python GC heap) soft
timers. This can be useful for a board to define a custom background
handler, or eventually for BLE/network processing to use instead of systick
slots; it will be more efficient using soft timer for this.
The main issue with using the existing code for static soft timers is that
it would combine heap allocated and statically allocated soft_timer_entry_t
instances in the same pairing-heap data structure. This would prevent the
GC from tracing some of the heap allocated entries (because the GC won't
follow pointers outside the heap).
This commit makes it so that soft timer entries are explicitly marked,
instead of relying on implicit marking by having the root of the pairing
heap in the root pointer section. Also, on soft reset only the heap-
allocated soft timers are deleted from the pairing heap, leaving the
statically allocated ones.
Signed-off-by: Damien George <damien@micropython.org>
This commit re-enables the command-line make option "FROZEN_MANIFEST". The
boards/*/mpconfigboard.cmake will now use the command-line FROZEN_MANIFEST
value if supplied.
Usage: make FROZEN_MANIFEST=~/foo/my-manifest.py
This introduces a new option, MICROPY_ERROR_REPORTING_NONE, which
completely disables all error messages. To be used in cases where
MicroPython needs to fit in very limited systems.
Signed-off-by: Damien George <damien@micropython.org>
Since version 21.4b0, Black now processes one-line docstrings by stripping
leading and trailing spaces, and adding a padding space when needed to
break up """"; see https://github.com/psf/black/pull/1740
This commit makes the Python code in this repository conform to this rule.
So this driver works on faster MCUs (that run this loop fast) with older,
slower SD cards.
Fixes issue #7129.
Signed-off-by: Damien George <damien@micropython.org>
Because "find_package(Python3 ...)" requires at least this version of
CMake. And other features like GREATER_EQUAL and COMMAND_EXPAND_LISTS need
at least CMake 3.7 and 3.8 respectively.
Signed-off-by: Damien George <damien@micropython.org>
This is now the default, but can be overridden with CLI `--no-exclusive`,
or constructing `Pyboard(..., exclusive=False)`.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds the errno attribute to exceptions, so code can retrieve
errno codes from an OSError using exc.errno.
The implementation here simply lets `errno` (and the existing `value`)
attributes work on any exception instance (they both alias args[0]). This
is for efficiency and to keep code size down. The pros and cons of this
are:
Pros:
- more compatible with CPython, less difference to document and learn
- OSError().errno will correctly return None, whereas the current way of
doing it via OSError().args[0] will raise an IndexError
- it reduces code size on most bare-metal ports (because they already have
the errno qstr)
- for Python code that uses exc.errno the generated bytecode is 2 bytes
smaller and more efficient to execute (compared with exc.args[0]); so
bytecode loaded to RAM saves 2 bytes RAM for each use of this attribute,
and bytecode that is frozen saves 2 bytes flash/ROM for each use
- it's easier/shorter to type, and saves 2 bytes of space in .py files that
use it (for each use)
Cons:
- increases code size by 4-8 bytes on minimal ports that don't already have
the `errno` qstr
- all exceptions now have .errno and .value attributes (a cpydiff test is
added to address this)
See also #2407.
Signed-off-by: Damien George <damien@micropython.org>
Improvements are:
- Default period is 1000ms with callback disabled.
- if period is not specified then it's not updated (previously, if period
was not specified then it was set to -1 and running the timer callback as
fast as possible, making the REPL unresponsive).
- Use uint64_t to compute delta_ms, and raise a ValueError if the period is
too large.
- If callback is not specified then it's not updated.
- Specifying None for the callback will disable the timer.
Signed-off-by: Damien George <damien@micropython.org>
The PIO state machines on the RP2040 have 4 word deep TX and RX FIFOs. If
you only need one direction, you can "merge" them into either a single 8
word deep TX or RX FIFO.
We simply add constants to the PIO object, and set the appropriate bits in
`shiftctrl`.
Resolves#6854.
Signed-off-by: Tim Radvan <tim@tjvr.org>
Commit 8a917ad252 added the gpio_reset_pin()
call to make sure that pins that were used as ADC inputs could subsequently
be used as digital IO. But calling gpio_reset_pin() will enable the
pull-up on the pin and so pull it high for a brief period. Instead use
rtc_gpio_deinit() which will just reconfigure the pin as a digital IO and
do nothing else.
Fixes issue #7079 (see also #5771).
Signed-off-by: Damien George <damien@micropython.org>
Commit cb68a5741a broke automatic Python
feature detection when running tests, because some detection relied on a
crash of a feature script returning exactly b"CRASH".
This commit fixes this and improves the situation by testing for the lack
of a known pass result, rather than an exact failure result.
Signed-off-by: Damien George <damien@micropython.org>
For an unconnected TCP socket, poll should return WR|HUP and read should
raise ENOTCONN. This is implemented by this commit and now the following
tests pass on esp32: extmod/usocket_tcp_basic.py,
net_hosted/connect_poll.py.
Signed-off-by: Damien George <damien@micropython.org>
This change allows running the tests in tests/basics/ without any failures
(but some tests are still skipped).
Signed-off-by: Damien George <damien@micropython.org>
This fixes `error: variable 'subpkg_tried' might be clobbered by 'longjmp'
or 'vfork' [-Werror=clobbered]` when compiling on ppc64le and aarch64 (and
possibly other architectures/toolchains).
This function includes the UART prescaler in the calculation (if it has
one, eg on H7 and WB MCUs).
Signed-off-by: Damien George <damien@micropython.org>
This allows configuring the pre-allocated size of sys.modules dict, in
order to prevent unwanted reallocations at run-time (3 sys-modules is
really not quite enough for a larger project).
When building with STATIC undefined (e.g., -DSTATIC=), there are two
instances of mp_type_code that collide at link time: in profile.c and in
builtinevex.c. This patch resolves the collision by renaming one of them.
The STM32WB has a problem when address resolution is enabled: under certain
conditions the MCU can get into a state where it draws an additional 10mA
or so and eventually ends up with a broken BLE RX path in the silicon. A
simple way to reproduce this is to enable address resolution (which is the
default for NimBLE) and start the device advertising. If there is enough
BLE activity in the vicinity then the device will at some point enter the
bad state and, if left long enough, will have permanent BLE RX damage.
STMicroelectronics are aware of this issue. The only known workaround at
this stage is to not enable address resolution, which is implemented by
this commit.
Work done in collaboration with Jim Mussared aka @jimmo.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this commit, if C2 was busy (eg lots of BLE activity) then it may
not have had time to respond to the notification on the IPCC_CH_MM channel
by the time additional memory was available to put on that buffer. In such
a case C1 would modify the free buffer list while C2 was potentially
accessing it, and this would eventually lead to lost memory buffers (or a
corrupt linked list). If all buffers become lost then ACL packets
(asynchronous events) can no longer be delivered from C2 to C1.
This commit fixes this issue by waiting for C2 to indicate that it has
finished using the free buffer list.
Work done in collaboration with Jim Mussared aka @jimmo.
Signed-off-by: Damien George <damien@micropython.org>
This change allows to build firmware for different rp2-based boards,
following how it is done in other ports like stm32 and esp32. So far only
the original Pico and Adafruit Feather RP2040 are added. Board names
should match (sans case) those in pico-sdk/src/boards/include/boards/.
Usage: Pico firmware can be build either using make as previously (it is
the default board) or by `make BOARD=PICO`. Feather is built by `make
BOARD=ADAFRUIT_FEATHER_RP2040`. Only the board name and flash drive size
is set, pin definition is taken from the appropriate pico-sdk board
definition. Firmware is saved in the directory build-BOARD_NAME.
Instantiation and init now support the rxbuf and txbuf keywords for setting
the buffer size. The default size is 256 bytes. The minimum and maximum
sizes are 32 and 32766 respectively.
uart.write() still includes checks for timeout, even if it is very unlikely
to happen due to a) lack of flow control support and b) the minimal timeout
values being longer than the time it needs to send a byte.
StateMachine.restart: Restarts the state machine
StateMachine.rx_fifo: Return the number of RX FIFO items, 0 if empty
StateMachine.tx_fifo: Return the number of TX FIFO items, 0 if empty
restart() seems to be the most useful one, as it resets the state machine
to the initial state without the need to re-initialise/re-create. It also
makes PIO code easier, because then stalling as an error state can be
unlocked.
rx_fifo() is also useful, for MP code to check for data and timeout if no
data arrived. Complex logic is easier handled in Python code than in PIO
code.
tx_fifo() can be useful to check states where data is not processed, and is
mostly for symmetry.
The implementation samples rosc.randombits at a frequency lower than the
oscillator frequency. This gives better random values. In addition, for
an 8-bit value 8 samples are taken and fed through a 8-bit CRC,
distributing the sampling over the byte. The resulting sampling rate is
about 120k/sec.
The RNG does not include testing of error conditions, like the ROSC being
in sync with the sampling or completely failing. Making the interim value
static causes it to perform a little bit better in short sync or drop-out
situations.
The output of uos.urandom() performs well with the NIST800-22 test suite.
In my trial it passed all tests of the sts 2.1.2 test suite. I also ran a
test of the random data with the Common Criteria test suite AIS 31, and it
passed all tests too.
There were a few changes that had broken this example, specifically
2cdf1d25f5 removed file.c from ports/unix.
And (at least for MacOS) mp_state_ctx must be placed in the BSS with
-fno-common so it is visible to the linker.
Signed-off-by: Santeri Paavolainen <santtu@iki.fi>
STM32L476RG MCU of NUCLEO_L476RG board has 6 UART/USART units in total
(USART1, USART2, USART3, UART4, UART5 and LPUART1), but only UART2,
connected to REPL, was defined and available in Python code.
Defined are all 5 remaining UART/USART units including LPUART1.
Signed-off-by: Alexander Ziubin aziubin@googlemail.com
This commit simplifies the customisation of the main MicroPython execution
loop (4 macros are reduced to 2), and allows a board to have full control
over the execution (or not) of boot.py and main.py.
For boards that use the default start-up code, there is no functional
change in this commit.
Signed-off-by: Damien George <damien@micropython.org>
Per CPython everything which comes after the command, module or file
argument is not an option for the interpreter itself. Hence the processing
of options should stop when encountering those, and the remainder be passed
as sys.argv. Note the latter was already the case for a module or file but
not for a command.
This fixes issues like 'micropython myfile.py -h' showing the help and
exiting instead of passing '-h' as sys.argv[1], likewise for
'-X <something>' being treated as a special option no matter where it
occurs on the command line.
Some forum users noticed that `sm.exec()` took longer the more was present
on the flash filesystem connected to the RP2040. They traced this back to
the `array` import inside `asm_pio()`, which is causing MicroPython to scan
the filesystem.
uarray is a built-in module, so importing it shouldn't require scanning the
filesystem.
We avoid moving the import to the top-level in order to keep the namespace
clean; we don't want to accidentally expose `rp2.array`.
The generated regex code is limited in the range of jumps and counts, and
this commit checks all cases which can overflow given the right kind of
input regex, and returns an error in such a case.
This change assumes that the results that overflow an int8_t do not
overflow a platform int.
Closes: #7078
Signed-off-by: Jeff Epler <jepler@gmail.com>
Support for C++ was added in 97960dc7de but
that commit didn't include the C++ exception handling table in the binary
firmware image. This commit fixes that.
Signed-off-by: Damien George <damien@micropython.org>
This is a workaround for errata RP2040-E5, and is needed to make USB more
reliable on certain USB ports.
Signed-off-by: Damien George <damien@micropython.org>
Make and CMake builds are slightly different and these changes help make it
clear what to do in each case.
Signed-off-by: Damien George <damien@micropython.org>
It's a bit of a pitfall with user C modules that including them in the
build does not automatically enable them. This commit changes the docs and
examples for user C modules to encourage writers of user C modules to
enable them unconditionally. This makes things simpler and covers most use
cases.
See discussion in issue #6960, and also #7086.
Signed-off-by: Damien George <damien@micropython.org>
It was noticed that the esp32 port didn't build ulab correctly. The
problem was a multiple defintion of the 'mp_hal_stdout_tx_str' and
'mp_hal_stdout_tx_strn_cooked' functions.
They were defined in stdout_helpers.c but also in the
ports/esp32/mphalport.c.
Fixed by removing stdout_helpers.c from the build.
Signed-off-by: Michael O'Cleirigh <michael.ocleirigh@rivulet.ca>
Support for User C and C++ modules was lost due to upgrading the esp32 to
the latest CMake based IDF from the GNUMakefile build process.
Restore the support for the esp32 port by integrating with the approach
recently added for the rp2 port.
Signed-off-by: Michael O'Cleirigh <michael.ocleirigh@rivulet.ca>
This USB feature is currently not supported. With this flag enabled (and
the feature not implemented) the USB serial will stop working if there is a
delay of more than about 2 seconds between messages, which can occur with
USB autosuspend enabled.
Fixes issue #6866.
Documents the micropython.cmake file required to make user C modules
compatible with the CMake build system.
Signed-off-by: Phil Howard <phil@pimoroni.com>
examples/usercmodule/micropython.cmake:
Root micropython.cmake file is responsible for including modules.
examples/usercmodule/cexample/micropython.cmake:
examples/usercmodule/cppexample/micropython.cmake:
Module micropython.cmake files define the target and link it to usermod.
Signed-off-by: Phil Howard <phil@pimoroni.com>
The parts that are generic are added to py/ so they can be used by other
ports that use CMake.
py/usermod.cmake:
* Creates a usermod target to hang user C/CXX modules from.
* Gathers sources from user C/CXX modules and libs for QSTR scan.
ports/rp2/CMakeLists.txt:
* Includes py/usermod.cmake.
* Links the resulting usermod library to the MicroPython target.
py/mkrules.cmake:
Add cxxflags to qstr.i.last custom command for CXX modules:
* MICROPY_CPP_FLAGS so CXX modules will find includes.
* -DNO_QSTR to fix fatal error missing "genhdr/qstrdefs.generated.h".
Usage:
The rp2 port can be linked against user C modules by running:
make USER_C_MODULES=/path/to/module/micropython.cmake
CMake will print a list of included modules.
Co-authored-by: Graham Sanderson <graham.sanderson@raspberrypi.org>
Co-authored-by: Michael O'Cleirigh <michael.ocleirigh@rivulet.ca>
Signed-off-by: Phil Howard <phil@pimoroni.com>
This commit simplifies and cleans up the bare-arm port, and adds just
enough system and library code to make it execute on an STM32F405 MCU.
The mpconfigport.h configuration is simplified to just specify those
configuration values that are different from the defaults. And the
addition of -fdata-sections and -ffunction-sections means the final
firmware is smaller than it previously was, by about 4200 bytes.
A README is also added.
Signed-off-by: Damien George <damien@micropython.org>
mp_printf should be used to print the prefix because it's also used in
mp_bytecode_print2 (otherwise, depending on the system, different output
streams may be used).
Also print the current thread state when threading is enabled to easily see
which thread executes what opcode.
Signed-off-by: Damien George <damien@micropython.org>
This helps to reduce memory fragmentation, by freeing the heap data as soon
as it is not needed. It also helps the compiler keeps a reference to the
beginning of both arrays, which need to be traceable by the GC (otherwise
some compilers may optimise this reference to something else).
Signed-off-by: Damien George <damien@micropython.org>
The GNU Make dir command uses spaces as item separator so it does not
work for e.g building the STM32 port on Cygwin with a default Arm
installation in "c:/program files (x86)/GNU Arm Embedded Toolchain".
Fix by using POSIX dirname on a quoted path instead.
Add most formatting-only commits to this file so that when used with
git blame, these commits are excluded and the output shows only the
interesting bits.
When UART is used for REPL and the MCU frequency is changed, the UART
has to be re-initialised. Besides that the UART may have to be recreated
after a frequency change, but with USB REPL this is not a problem.
Thanks to @HermannSW for spotting and providing the change.
Using the standard machine.freq().
The safe ranges tested were 10 and 12-270MHz, at which USB REPL still
worked. Requested settings can be checked with the script:
pico-sdk/src/rp2_common/hardware_clocks/scripts/vcocalc.py. At frequencies
like 300MHz the script still signaled OK, but USB did not work any more.
sm.get(buf) was waiting for one item more than the length of the supplied
buffer. Even if this item was not stored, sm_get would block trying to get
an item from the RX fifo.
As part of the fix, the edge case for a zero length buffer was moved up to
the section where the function arguments are handled. In case of a zero
length buffer, sm.get() now returns immediately that buffer.
The bitmasks supplied for initialization of out/set/sideset were only 8 bit
instead of 32. This resulted in an error, that not more than 8 consecutive
pins would get initialized.
Fixes issue #6933.
From a version numbering point of view this is a downgrade (2.17.0 ->
2.16.x). However the latest commit for version 2.17.0 is from March 2019
and no further minor release happened after 2.17.0. This version is EOL.
2.16.x though is still actively maintained as a long term release, hence
security and stability fixes are still being backported, including
compatibility with upcoming compiler releases.
This allows the user to enable wake-up sources using the EWUP bits, on F7
MCUs.
Disabling the wake-up sources while clearing the wake-up flags follows the
reference manual and ST examples.
state.reset_mode is updated by `MICROPY_BOARD_BEFORE_SOFT_RESET_LOOP` but
not passed to `init_flash_fs`, and so factory reset is not executed on
boards that do not have a bootloader. This bug was introduced by
4c3976bbcaFixes#6903.
A corrupt filesystem may lead to a request for a block which is out of
range of the block device limits. Return an error instead of passing the
request down to the lower layer.
Two of the defaults have also changed in this commit:
- MICROPY_HW_RFCORE_BLE_LSE_SOURCE changed from 1 to 0, which configures
the LsSource to be LSE (needed due to errata 2.2.1).
- MICROPY_HW_RFCORE_BLE_VITERBI_MODE changed from 0 to 1, which enables
Viterbi mode, following all the ST examples.
Signed-off-by: Damien George <damien@micropython.org>
Instead of raising a ZeroDivisionError, this tool now just skips any
elements in the DFU file that have zero size.
Signed-off-by: Damien George <damien@micropython.org>
These ports already have uzlib enabled so this additional ubinascii.crc32
function only costs about 90 bytes of flash.
Signed-off-by: Damien George <damien@micropython.org>
This allows a port to specify a custom qstrdefsport.h file, the same as the
QSTR_DEFS variable in a Makefile.
Signed-off-by: Damien George <damien@micropython.org>
Add LPUART1 as a standard UART. No low power features are supported, yet.
LPUART1 is enabled as the next available UART after the standard U(S)ARTs:
STM32WB: LPUART1 = UART(2)
STM32L0: LPUART1 = UART(6)
STM32L4: LPUART1 = UART(6)
STM32H7: LPUART1 = UART(9)
On all ports: LPUART1 = machine.UART('LP1')
LPUART1 is enabled by defining MICROPY_HW_LPUART1_TX and
MICROPY_HW_LPUART1_RX in mpconfigboard.h.
Signed-off-by: Chris Mason <c.mason@inchipdesign.com.au>
Previously, the MICROPY_PY_BLUETOOTH_ENABLE_CENTRAL_MODE macro
controlled enabling both the central mode and the GATT client
functionality (because usually the two go together).
This commits adds a new MICROPY_PY_BLUETOOTH_ENABLE_GATT_CLIENT
macro that separately enables the GATT client functionality.
This defaults to MICROPY_PY_BLUETOOTH_ENABLE_CENTRAL_MODE.
This also fixes a bug in the NimBLE bindings where a notification
or indication would not be received by a peripheral (acting as client)
as gap_event_cb wasn't handling it. Now both central_gap_event_cb
and peripheral_gap_event_cb share the same common handler for these
events.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit fixes two issues on the esp32:
- it enables machine.soft_reset() to be called in main.py;
- it enables machine.reset_cause() to correctly identify a soft reset.
The former is useful in that it enables soft resets in applications that
are started at boot time. The support is patterned after the stm32 port.
This commit implements basic NVS support for the esp32. It follows the
pattern of the esp32.Partition class and exposes an NVS object per NVS
namespace. The initial support provided is only for signed 32-bit integers
and binary blobs. It's easy (albeit a bit tedious) to add support for
more types.
See discussions in: #4436, #4707, #6780
This enables -Os for compilation, but still keeps full assertion messages.
With IDF v4.2, -Os changes the GENERIC firmware size from 1512176 down to
1384640, and the GENERIC_SPIRAM firmware is now 1452320 which fits in the
allocated partition.
Signed-off-by: Damien George <damien@micropython.org>
So that mboot can be used to program encrypted/signed firmware to regions
of flash that are not the main application, eg that are the filesystem.
Signed-off-by: Damien George <damien@micropython.org>
The default for these is to enable them, but they can now be disabled
individually by a board configuration.
Signed-off-by: Damien George <damien@micropython.org>
If a board defines USBD_VID then that will be used instead of the default.
And then the board must also define all USBD_PID_xxx values that it needs.
Signed-off-by: Damien George <damien@micropython.org>
Zephyr controllers can be queried for a static address (computed from the
device ID). BlueKitchen already supports this, but make them both use the
same macro to enable the feature.
The following simple usocket example throws an error EINVAL on connect
import usocket
s = usocket.socket()
s.connect(usocket.getaddrinfo('www.micropython.org', 80)[0][-1])
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
OSError: [Errno 22] EINVAL
Fixing the context parameter in calls of net_context_get_family() and
net_context_get_type(), the connect works fine.
Tested on a nucleo_h743zi board.
Updates the zephyr docker image to the latest, v0.11.13. This updates CI
to use zephyr SDK v0.12.2 and GCC v10.2.0 for the zephyr port.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the zephyr build infrastructure to build MicroPython as a
cmake target, using the recently introduced core cmake rules.
This change makes it possible to build the zephyr port like most other
zephyr applications using west or cmake directly. It simplifies building
with extra cmake arguments, such as specifying an alternate conf file or
adding an Arduino shield. It also enables building the zephyr port
anywhere in the host file system, which will allow regressing across
multiple boards with the zephyr twister script.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Disables frozen source modules in the zephyr port. They are deprecated
in the makefile rules and not implemented in the new cmake rules.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The core cmake rules use custom commands to invoke qstr processing
scripts. For the zephyr port, it's possible that list arguments to these
commands may contain generator expressions, therefore we need to expand
them properly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This allows customising which features can be enabled in a frozen library.
e.g. `include("path.py", extra_features=True)`
in path.py:
options.defaults(standard_features=True)
if options.standard_features:
# freeze standard modules.
if options.extra_features:
# freeze extra modules.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is a MicroPython-extension that allows for code running in IRQ
(hard or soft) or scheduler context to sequence asyncio code.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
On error, the handle is only available on err->att_handle rather than
in attr->handle used in the non-error case.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The underlying OS (the ESP-IDF) uses it's own internal errno codes and so
it's simpler and cleaner to use those rather than trying to convert
everything to the values defined in py/mperrno.h.
It's now replaced by cmake/idf.py. But a convenience Makefile is still
provided with traditional targets like "all" and "deploy".
Signed-off-by: Damien George <damien@micropython.org>
This commit adds support for building the esp32 port with cmake, and in
particular it builds MicroPython as a component within the ESP-IDF. Using
cmake and the ESP-IDF build infrastructure makes it much easier to maintain
the port, especially with the various new ESP32 MCUs and their required
toolchains.
Signed-off-by: Damien George <damien@micropython.org>
This allows changing the baudrate of the UART without reinitialising it
(reinitialising can lead to spurious characters sent on the TX line).
Signed-off-by: Damien George <damien@micropython.org>
On i.MX the SysTick IRQ cannot wake the CPU from a WFI so the CPU was
blocked on WFI waiting for USB data in mp_hal_stdin_rx_chr() even though it
had already arrived (because it may arrive just after calling the check
tud_cdc_available()). This commit fixes this problem by using SEV/WFE to
indicate that there has been a USB event.
The mp_hal_stdout_tx_strn() function is also fixed so that it doesn't
overflow the USB buffers.
Signed-off-by: Damien George <damien@micropython.org>
So that all MicroPython ports that use tinyusb use the same version. Also
requires fewer submodule checkouts when building rp2 along with other ports
that use tinyusb.
Signed-off-by: Damien George <damien@micropython.org>
START_SEC was changed in e0905e85a7.
Also, update the error message to mention how to format the partition at
the REPL, and make the total message shorter to save a bit of flash.
Signed-off-by: Damien George <damien@micropython.org>
For certain operands to mpn_div, the existing code path for
`DIG_SIZE == MPZ_DBL_DIG_SIZE / 2` had a bug in it where borrow could still
overflow in the `(x >= *n || *n - x <= borrow)` branch, ie
`borrow + x - (mpz_dbl_dig_t)*n` overflows the borrow variable. In such
cases the subsequent right-shift of borrow would not bring in the overflow
bit, leading to an error in the result. An example division that had
overflow when MPZ_DIG_SIZE = 16 is `(2 ** 48 - 1) ** 2 // (2 ** 48 - 1)`.
This is fixed in this commit by simplifying the code and handling the low
digits of borrow first, and then the upper bits (to shift down) separately.
There is no longer a distinction between `DIG_SIZE < MPZ_DBL_DIG_SIZE / 2`
and `DIG_SIZE == MPZ_DBL_DIG_SIZE / 2`.
This commit also simplifies the second part of the calculation so that
borrow does not need to be negated (instead the code just works knowing
that borrow is negative and using + instead of - in calculations involving
borrow).
Fixes#6777.
Signed-off-by: Damien George <damien@micropython.org>
In particular the firmware can now be built in a build directory that lives
outside the source tree, and the py/modarray.c file will still be found.
See issue #6837.
Signed-off-by: Damien George <damien@micropython.org>
The "word" referred to by BYTES_PER_WORD is actually the size of mp_obj_t
which is not always the same as the size of a pointer on the target
architecture. So rename this config value to better reflect what it
measures, and also prefix it with MP_.
For uses of BYTES_PER_WORD in setting the stack limit this has been
changed to sizeof(void *), because the stack usually grows with
machine-word sized values (eg an nlr_buf_t has many machine words in it).
Signed-off-by: Damien George <damien@micropython.org>
It's only used in one location, to test if << or >> will overflow when
shifting mp_uint_t. For such a test it's clearer to use sizeof(lhs_val),
which will be valid even if the type of lhs_val changes.
Signed-off-by: Damien George <damien@micropython.org>
To simplify config, there's no need to specify MP_PLAT_PRINT_STRN if it's
the same as the default definition in py/mpconfig.h.
Signed-off-by: Damien George <damien@micropython.org>
Otherwise it resets the ADC peripheral each time a new ADC object is
constructed, which can reset other state that has already been set up.
See issue #6833.
Signed-off-by: Damien George <damien@micropython.org>
Default to just calling python since that is most commonly available: the
official installer or zipfiles from python.org, anaconda, nupkg all result
in python being available but not python3. In other words: the default
used so far is wrong. Note that os.name is 'posix' when running the python
version which comes with Cygwin or MSys2 so they are not affected by this.
However of all possible ways to get Python on Windows, only Cygwin provides
no python command so update the default way for running tests in the
README.
With mboot encrpytion and fsload enabled, the DEBUG build -O0 compiler
settings result in mboot no longer fitting in the 32k sector. This commit
changes this to -Og which also brings it into line with the regular stm32
build.
MCUs with device-only USB peripherals (eg L0, WB) do not implement (at
least not in the ST HAL) the HAL_PCD_DisconnectCallback event. So if a USB
cable is disconnected the USB driver does not deinitialise itself
(usbd_cdc_deinit is not called) and the CDC driver can stay in the
USBD_CDC_CONNECT_STATE_CONNECTED state. Then if the USB was attached to
the REPL, output can become very slow waiting in usbd_cdc_tx_always for
500ms for each character.
The disconnect event is not implemented on these MCUs but the suspend event
is. And in the situation where the USB cable is disconnected the suspend
event is raised because SOF packets are no longer received.
The issue of very slow output on these MCUs is fixed in this commit (really
worked around) by adding a check in usbd_cdc_tx_always to see if the USB
device state is suspended, and, if so, breaking out of the 500ms wait loop.
This should also help all MCUs for a real USB suspend.
A proper fix for MCUs with device-only USB would be to implement or somehow
synthesise the HAL_PCD_DisconnectCallback event.
See issue #6672.
Signed-off-by: Damien George <damien@micropython.org>
PIO state machines can make a conditional jump on the state of a pin: the
`JMP PIN` command. This requires the pin to be configured with
`sm_config_set_jmp_pin`, but until now we didn't have a way of doing that
in MicroPython.
This commit adds a new `jmp_pin=None` argument to `StateMachine`. If it is
not `None` then we try to interpret it as a Pin, and pass its value to
`sm_config_set_jmp_pin`.
Signed-off-by: Tim Radvan <tim@tjvr.org>
Some devices have lower precision than 1ms for time_ns() (eg PYBv1.x has
3.9ms resolution of the RTC) so make the test more lenient for them.
Signed-off-by: Damien George <damien@micropython.org>
With a check for reproducible build date. Invocation of the test suite is
not needed because it's already run in another job.
Signed-off-by: iTitou <moiandme@gmail.com>
This environment variable, if defined during the build process,
indicates a fixed time that should be used in place of "now" when
such a time is explicitely referenced.
This allows for reproducible builds of micropython.
See https://reproducible-builds.org/specs/source-date-epoch/
Signed-off-by: iTitou <moiandme@gmail.com>
This should be enabled when the mp_raw_code_save_file function is needed.
It is enabled for mpy-cross, and a check for defined(__APPLE__) is added to
cover Mac M1 systems.
The upip module is frozen into ports supporting it, and it is included in
the source tree, so there is no need to get it from PyPi. Moreover the
PyPi package referred to is an out-of-date version of upip which is
basically unrelated to our upip.py because the source is taken from a fork
of micropython-lib instead of this repository.
Add "make submodules" to commands when building for the first time.
Otherwise, on a first time build, the submodules have not been checked out
and a lot of `fatal error: nrfx.h: No such file or directory` errors are
printed.
The main rules enforced are:
- At most 72 characters in the subject line, with a ": " in it.
- At most 75 characters per line in the body.
- No "noreply" email addresses.
This was added a long time ago in 75abee206d
when USB host support was added to the stm (now stm32) port, and when this
pyexec code was actually part of the stm port. It's unlikely to work as
intended anymore. If it is needed in the future then generic hook macros
can be added in pyexec.
It practically does the same as qstr_from_str and was only used in one
place, which should actually use the compile-time MP_QSTR_XXX form for
consistency; qstr_from_str is for runtime strings only.
If the _IRQ_L2CAP_RECV handler does the actual consumption of the incoming
data (i.e. via l2cap_recvinto), rather than setting a flag for
non-scheduler-context to handle it later, then two things can happen:
- It can starve the VM (i.e. the scheduled task never terminates). This is
because calling l2cap_recvinto will empty the rx buffer, which will grant
more credits to the channel (an HCI command), meaning more data can
arrive. This means that the loop in hal_uart.c that keeps reading HCI
data from the uart and executing NimBLE events as they are created will
not terminate, preventing other VM code from running.
- There's no flow control (i.e. data will arrive too quickly). The channel
shouldn't be given credits until after we return from scheduler context.
It's preferable that no work is done in scheduler/IRQ context. But to
prevent this being a problem this commit changes l2cap_recvinto so that if
it is called in IRQ context, and the Python handler empties the rx buffer,
then don't grant credits until the Python handler is complete.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Don't clear the IPCC channel flag until we've actually handled the incoming
data, or else the wireless firmware may clobber the IPCC buffer if more
data arrives. This requires masking the IRQ until the data is handled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds a new port "rp2" which targets the new Raspberry Pi RP2040
microcontroller.
The build system uses pure cmake (with a small Makefile wrapper for
convenience). The USB driver is TinyUSB, and there is a machine module
with most of the standard classes implemented. Some examples are provided
in the examples/rp2/ directory.
Work done in collaboration with Graham Sanderson.
Signed-off-by: Damien George <damien@micropython.org>
These args are already bounds checked and clipped, and using unsigned ints
can be more efficient. It also eliminates possible issues and compiler
warnings with shifting of signed integers.
Signed-off-by: Damien George <damien@micropython.org>
Adds a new compile-time option MICROPY_EMIT_THUMB_ARMV7M which is enabled
by default (to get existing behaviour) and which should be disabled (set to
0) when building native emitter support (@micropython.native) on ARMv6M
targets.
This returns a reference to the globals dict associated with the function,
ie the global scope that the function was defined in. This attribute is
read-only but the dict itself is modifiable, per CPython behaviour.
Signed-off-by: Damien George <damien@micropython.org>
It's enabled by default to retain the existing behaviour. A board can
disable this option if it manages mounting the filesystem itself, for
example in frozen code.
Signed-off-by: Damien George <damien@micropython.org>
Changes are:
- refactor to use new _create_element function
- support extended version of MOUNT element with block size
- support STATUS element
Signed-off-by: Damien George <damien@micropython.org>
This new element takes the form: (ELEM_TYPE_STATUS, 4, <address>). If this
element is present in the mboot command then mboot will store to the given
address the result of the filesystem firmware update process. The address
can for example be an RTC backup register.
Signed-off-by: Damien George <damien@micropython.org>
Instead it is now passed in as an optional parameter to the ELEM_MOUNT
element, with a compile-time configurable default.
Signed-off-by: Damien George <damien@micropython.org>
The superblock for littlefs is in block 0 and 1, but block 0 may be erased
or partially written, so block 1 must be checked if block 0 does not have a
valid littlefs superblock in it.
Prior to this commit, if block 0 did not contain a valid littlefs
superblock (but block 1 did) then the auto-detection would fail, mounting a
FAT filesystem would also fail, and the system would reformat the flash,
even though it may have contained a valid littlefs filesystem. This is now
fixed.
Signed-off-by: Damien George <damien@micropython.org>
The superblock for littlefs is in block 0 and 1, but block 0 may be erased
or partially written, so block 1 must be checked if block 0 does not have a
valid littlefs superblock in it.
Prior to this commit, the mount of a block device which auto-detected the
filysystem type would fail for littlefs if block 0 did not contain a valid
superblock. That is now fixed.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds many new sections to the existing "Developing and building
MicroPython" chapter to make it all about the internals of MicroPython.
This work was done as part of Google's Season of Docs 2020.
Changes are:
- Use ubuntu-20.04 so that gcc-multilib installs without error.
- Use "fetch-depth: 100" to get history prior to pull request.
Signed-off-by: Damien George <damien@micropython.org>
* Fix a typo in the Makefile that prevented the debug build to be actually
enabled when BTYPE=debug is used.
* Add a missing header in modmachine.c that is used when a debug build is
created.
This commit improves some FTP implementation details for better
compatibility with FTP clients:
* The PWD command now puts quotes around the directory name before
returning it. This fixes BBEdit’s FTP client, which performs a PWD after
each CWD and gets confused if the returned directory path is not
surrounded by quotes.
* The FEAT command is now allowed before logging in. This fixes the lftp
client, which send FEAT first and gets confused (tries to use TLS) if the
server responds with 332.
With MICROPY_FLOAT_IMPL_FLOAT the results of utime.time(), gmtime() and
localtime() change only every 129 seconds. As one consequence
tests/extmod/vfs_lfs_mtime.py will fail on a unix port with LFS support.
With this patch these functions only return floats if
MICROPY_FLOAT_IMPL_DOUBLE is used. Otherwise they return integers.
According to documentation time() has a precision of at least 1 second.
This test runs for 2.5 seconds and calls all utime functions every 100ms.
Then it checks if they returned enough different results. All functions
with sub-second precision will return ~25 results. This test passes with
15 results or more. Functions that do not exist are skipped silently.
This allows sending arbitrary HCI commands and getting the response. The
return value of the function is the status of the command.
This is intended for debugging and not to be a part of the public API, and
must be enabled via mpconfigboard.h. It's currently only implemented for
NimBLE bindings.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
To match the definition of GENERATE_PACK_DFU, so a board can customise the
location/name of this file if needed.
Signed-off-by: Damien George <damien@micropython.org>
To have at least one board configured with MBOOT_ENABLE_PACKING, for CI
testing purposes and demonstration of the feature.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds support to stm32's mboot for signe, encrypted and
compressed DFU updates. It is based on inital work done by Andrew Leech.
The feature is enabled by setting MBOOT_ENABLE_PACKING to 1 in the board's
mpconfigboard.mk file, and by providing a header file in the board folder
(usually called mboot_keys.h) with a set of signing and encryption keys
(which can be generated by mboot_pack_dfu.py). The signing and encryption
is provided by libhydrogen. Compression is provided by uzlib. Enabling
packing costs about 3k of flash.
The included mboot_pack_dfu.py script converts a .dfu file to a .pack.dfu
file which can be subsequently deployed to a board with mboot in packing
mode. This .pack.dfu file is created as follows:
- the firmware from the original .dfu is split into chunks (so the
decryption can fit in RAM)
- each chunk is compressed, encrypted, a header added, then signed
- a special final chunk is added with a signature of the entire firmware
- all chunks are concatenated to make the final .pack.dfu file
The .pack.dfu file can be deployed over USB or from the internal filesystem
on the device (if MBOOT_FSLOAD is enabled).
See #5267 and #5309 for additional discussion.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this fix, the final piece of data in a compressed file may have
been lost when decompressing.
Signed-off-by: Damien George <damien@micropython.org>
This library is a small and easy-to-use cryptographic library which is well
suited to embedded systems.
Signed-off-by: Damien George <damien@micropython.org>
The original logic of reducing a full path to a relative one assumes
"tests/misc" is in the filename which is limited in usage: it never works
for CPython on Windows since that will use a backslash as path separator,
and also won't work when the filename is a path not relative to the tests
directory which happens for example in the common case of running
"./run-tests -d misc".
Fix all cases by printing only the bare filename, which requires them all
to start with sys_settrace_ hence the renaming.
Changes are:
- Remove include of stm32's adc.h because it was recently changed and is
no longer compatible with teensy (and not used anyway).
- Remove define of __disable_irq in mpconfigport.h because it was clashing
with an equivalent definition in core/mk20dx128.h.
- Add -Werror to CFLAGS, and change -std=gnu99 to -std=c99.
Signed-off-by: Damien George <damien@micropython.org>
Mboot builds do not use the external SPI flash in caching mode, and
explicitly disabling it saves RAM and a small bit of flash.
Signed-off-by: Damien George <damien@micropython.org>
This only needs to be enabled if a board uses FAT FS on external SPI flash.
When disabled (and using external SPI flash) 4k of RAM can be saved.
Signed-off-by: Damien George <damien@micropython.org>
When littlefs is enabled extended reading must be supported, and using this
function to read the first block for auto-detection is more efficient (a
smaller read) and does not require a cached SPI-flash read.
Signed-off-by: Damien George <damien@micropython.org>
These functions enable SDRAM data retention in stop mode. Example usage,
in mpconfigboard.h:
#define MICROPY_BOARD_ENTER_STOP sdram_enter_low_power();
#define MICROPY_BOARD_LEAVE_STOP sdram_leave_low_power();
Calculate the bit timing from baudrate if provided, allowing sample point
override. This makes it a lot easier to make CAN work between different
MCUs with different clocks, prescalers etc.
Tested on F4, F7 and H7 Y/V variants.
This commit prevents uos.mount() from raising an AttributeError.
vfs_autodetect() is supposed to return an object that has a "mount" method,
so if no filesystem is found it should raise an OSError(ENODEV) and not
return the bdev itself which has no "mount" method.
Mounting a bdev directly tries to auto-detect the filesystem and if none is
found an OSError(19,) should be raised.
The fourth parameter of readblocks() and writeblocks() must be optional to
support ports with MICROPY_VFS_FAT=1. Otherwise mounting a bdev may fail
because looking for a FATFS will call readblocks() with only 3 parameters.
Since CPython 3.8 the optional "sep" argument to hexlify is officially
supported, so update comments in the code and the docs to reflect this.
Signed-off-by: Damien George <damien@micropython.org>
As a general pattern, required positional arguments that are not named do
not need to be parsed using mp_arg_parse_all().
Signed-off-by: Damien George <damien@micropython.org>
Because the version included in xtensa-lx106-elf-standalone.tar.gz needs
Python 2 (and pyserial for Python 2).
Signed-off-by: Damien George <damien@micropython.org>
This much buffer space is required for CDC data out endpoints to avoid any
buffer overflows when the USB CDC is saturated with data.
Signed-off-by: Damien George <damien@micropython.org>
The nrf52840-mdk-usb-dongle and pca10050 comes with a pre-flashed
bootloader (OpenBootloader).
This commit updates the boards "mpconfigboard.mk" to use DFU as
default flashing method and set the corresponding BOOTLOADER
settings such that nrf52840_open_bootloader_1.2.x.ld linker
script is used.
The default DFU flashing method can be disabled by issuing "DFU=0"
when invoking make. This will lead to "segger" being used as default
flashing tool. When using "DFU=0", the linker scripts will not
compensate for any MBR and Bootloader region being present, and might
overwrite them if they were present.
The commit also removes the custom linker script specific to
nrf52840-mdk-usb-dongle as it now points to a generic.
Updated nrf52840-mdk-usb-dongle's README.md to be more clear on
how to deploy the built firmware.
The port README.md has also been updated. In the list of target
boards a new column has been added to indicate which bootloader
is present on the target board. And for consistency, changed all
examples in the README.md to use "deploy" instead of "flash".
An additional Makefile parameter NRFUTIL_PORT can be set in order
to define the serial port to used for the DFU (Default: /dev/ttyACM0).
The "nrfutil" that is used as flasher towards OpenBootloader is
available for installation through Python "pip".
In case of SD=s140, SoftDevice ID 0xB6 is passed to nrfutil's package
generation which corresponds to SoftDevice s140 v6.1.1.
Add the option for "mpconfigboard.mk" to define whether the
board hosts a bootloader or not. The BOOTLOADER make variable
must be set to the name of the bootloader.
When the BOOTLOADER name is set it is also required to supply
the BOOTLOADER_VERSION_MAJOR and the BOOTLOADER_VERSION_MINOR
from the "mpconfigboards.mk". These will be used to resolve which
bootloader linker script that should be passed to the linker.
The BOOTLOADER section also supplies the C-compiler with
BOOTLOADER_<bootloader name>=<version major><version minor>
as a compiler define. This is for future use in case a bootloader
needs to do modification to the startup files or similar (like
setting the VTOR specific to a version of a bootloader).
Adding variables that can be set from other linker scripts:
- _bootloader_head_size:
Bootloader flash offset in front of the application.
- _bootloader_tail_size:
Bootloader offset from the tail of the flash.
In case the bootloader is located at the end.
- _bootloader_head_ram_size:
Bootloader RAM usage in front of the application.
Updated calculations of application flash and RAM.
Two issues are tackled:
1. The calculation of the correct length to print is fixed to treat the
precision as a maximum length instead as the exact length.
This is done for both qstr (%q) and for regular str (%s).
2. Fix the incorrect use of mp_printf("%.*s") to mp_print_strn().
Because of the fix of above issue, some testcases that would print
an embedded null-byte (^@ in test-output) would now fail.
The bug here is that "%s" was used to print null-bytes. Instead,
mp_print_strn is used to make sure all bytes are outputted and the
exact length is respected.
Test-cases are added for both %s and %q with a combination of precision
and padding specifiers.
The zephyr function net_shell_cmd_iface() was removed in zephyr v1.14.0,
therefore the MicroPython zephyr port did not build with newer zephyr
versions when CONFIG_NET_SHELL=y. Replace with a more general
shell_exec() function that can execute any zephyr shell command. For
example:
>>> zephyr.shell_exec("net")
Subcommands:
allocs :Print network memory allocations.
arp :Print information about IPv4 ARP cache.
conn :Print information about network connections.
dns :Show how DNS is configured.
events :Monitor network management events.
gptp :Print information about gPTP support.
iface :Print information about network interfaces.
ipv6 :Print information about IPv6 specific information and
configuration.
mem :Print information about network memory usage.
nbr :Print neighbor information.
ping :Ping a network host.
pkt :net_pkt information.
ppp :PPP information.
resume :Resume a network interface
route :Show network route.
stacks :Show network stacks information.
stats :Show network statistics.
suspend :Suspend a network interface
tcp :Connect/send/close TCP connection.
vlan :Show VLAN information.
websocket :Print information about WebSocket connections.
>>> zephyr.shell_exec("kernel")
kernel - Kernel commands
Subcommands:
cycles :Kernel cycles.
reboot :Reboot.
stacks :List threads stack usage.
threads :List kernel threads.
uptime :Kernel uptime.
version :Kernel version.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The -Og optimisation level produces a more realistic build, gives a better
debugging experience, and generates smaller code than -O0, allowing debug
builds to fit in flash.
This commit also assigns variables in can.c to prevent warnings when -Og is
used, and builds a board in CI with DEBUG=1 enabled.
Signed-off-by: Damien George <damien@micropython.org>
Allows reserving CAN, I2C, SPI, Timer and UART peripherals. If reserved
the peripheral cannot be accessed from Python.
Signed-off-by: Damien George <damien@micropython.org>
Even though IRQs are disabled this seems to be required on H7 Rev Y,
otherwise Systick interrupt triggers and the MCU leaves the stop mode
immediately.
This commit saves OSCs/PLLs state before STOP mode and restores them on
exit. Some boards use HSI48 for USB for example, others have PLL2/3
enabled, etc.
Rather than dealing with the different int types, just pass them all as a
single array of mp_int_t with n_unsigned (before addr) and n_signed (after
addr).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This adds `_IRQ_GET_SECRET` and `_IRQ_SET_SECRET` events to allow the BT
stack to request the Python code retrive/store/delete secret key data. The
actual keys and values are opaque to Python and stack-specific.
Only NimBLE is implemented (pending moving btstack to sync events). The
secret store is designed to be compatible with BlueKitchen's TLV store API.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This allows the application to be notified if any of encrypted,
authenticated and bonded state change, as well as the encryption key size.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Enable it on STM32/Unix NimBLE only (pairing/bonding requires synchronous
events and full bindings).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Instead of returning None/bool from the IRQ, return None/int (where a zero
value means success). This mirrors how the L2CAP_ACCEPT return value
works.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This widens the characteristic/descriptor flags to 16-bit, to allow setting
encryption/authentication requirements.
Sets the required flags for NimBLE and btstack implementations.
The BLE.FLAG_* constants will eventually be deprecated in favour of copy
and paste Python constants (like the IRQs).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This allows the application to be notified of changes to the connection
interval, connection latency and supervision timeout.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit switches the roles of the helper task from a cancellation task
to a runner task, to get the correct semantics for cancellation of
wait_for.
Some uasyncio tests are now disabled for the native emitter due to issues
with native code generation of generators and yield-from.
Fixes#5797.
Signed-off-by: Damien George <damien@micropython.org>
This is added because task.coro==None is no longer the way to detect if a
task is finished. Providing a (CPython compatible) function for this
allows the implementation to be abstracted away.
Signed-off-by: Damien George <damien@micropython.org>
When a tasks raises an exception which is uncaught, and no other task
await's on that task, then an error message is printed (or a user function
called) via a call to Loop.call_exception_handler. In CPython this call is
made when the Task object is freed (eg via reference counting) because it's
at that point that it is known that the exception that was raised will
never be handled.
MicroPython does not have reference counting and the current behaviour is
to deal with uncaught exceptions as early as possible, ie as soon as they
terminate the task. But this can be undesirable because in certain cases
a task can start and raise an exception immediately (before any await is
executed in that task's coro) and before any other task gets a chance to
await on it to catch the exception.
This commit changes the behaviour so that tasks which end due to an
uncaught exception are scheduled one more time for execution, and if they
are not await'ed on by the next scheduling loop, then the exception handler
is called (eg the exception is printed out).
Signed-off-by: Damien George <damien@micropython.org>
This commit adds support to pyboard.py for the new raw REPL paste mode.
Note that this new pyboard.py is fully backwards compatible with old
devices (it detects if the device supports the new raw REPL paste mode).
Signed-off-by: Damien George <damien@micropython.org>
Background: the friendly/normal REPL is intended for human use whereas the
raw REPL is for computer use/automation. Raw REPL is used for things like
pyboard.py script_to_run.py. The normal REPL has built-in flow control
because it echos back the characters. That's not so with raw REPL and flow
control is just implemented by rate limiting the amount of data that goes
in. Currently it's fixed at 256 byte chunks every 10ms. This is sometimes
too fast for slow MCUs or systems with small stdin buffers. It's also too
slow for a lot of higher-end MCUs, ie it could be a lot faster.
This commit adds a new raw REPL mode which includes flow control: the
device will echo back a character after a certain number of bytes are sent
to the host, and the host can use this to regulate the data going out to
the device. The amount of characters is controlled by the device and sent
to the host before communication starts. This flow control allows getting
the maximum speed out of a serial link, regardless of the link or the
device at the other end.
Also, this new raw REPL mode parses and compiles the incoming data as it
comes in. It does this by creating a "stdin reader" object which is then
passed to the lexer. The lexer requests bytes from this "stdin reader"
which retrieves bytes from the host, and does flow control. What this
means is that no memory is used to store the script (in the existing raw
REPL mode the device needs a big buffer to read in the script before it can
pass it on to the lexer/parser/compiler). The only memory needed on the
device is enough to parse and compile.
Finally, it would be possible to extend this new raw REPL to allow bytecode
(.mpy files) to be sent as well as text mode scripts (but that's not done
in this commit).
Some results follow. The test was to send a large 33k script that contains
mostly comments and then prints out the heap, run via pyboard.py large.py.
On PYBD-SF6, prior to this PR:
$ ./pyboard.py large.py
stack: 524 out of 23552
GC: total: 392192, used: 34464, free: 357728
No. of 1-blocks: 12, 2-blocks: 2, max blk sz: 2075, max free sz: 22345
GC memory layout; from 2001a3f0:
00000: h=hhhh=======================================hhBShShh==h=======h
00400: =====hh=B........h==h===========================================
00800: ================================================================
00c00: ================================================================
01000: ================================================================
01400: ================================================================
01800: ================================================================
01c00: ================================================================
02000: ================================================================
02400: ================================================================
02800: ================================================================
02c00: ================================================================
03000: ================================================================
03400: ================================================================
03800: ================================================================
03c00: ================================================================
04000: ================================================================
04400: ================================================================
04800: ================================================================
04c00: ================================================================
05000: ================================================================
05400: ================================================================
05800: ================================================================
05c00: ================================================================
06000: ================================================================
06400: ================================================================
06800: ================================================================
06c00: ================================================================
07000: ================================================================
07400: ================================================================
07800: ================================================================
07c00: ================================================================
08000: ================================================================
08400: ===============================================.....h==.........
(349 lines all free)
(the big blob of used memory is the large script).
Same but with this PR:
$ ./pyboard.py large.py
stack: 524 out of 23552
GC: total: 392192, used: 1296, free: 390896
No. of 1-blocks: 12, 2-blocks: 3, max blk sz: 40, max free sz: 24420
GC memory layout; from 2001a3f0:
00000: h=hhhh=======================================hhBShShh==h=======h
00400: =====hh=h=B......h==.....h==....................................
(381 lines all free)
The only thing in RAM is the compiled script (and some other unrelated
items).
Time to download before this PR: 1438ms, data rate: 230,799 bits/sec.
Time to download with this PR: 119ms, data rate: 2,788,991 bits/sec.
So it's more than 10 times faster, and uses significantly less RAM.
Results are similar on other boards. On an stm32 board that connects via
UART only at 115200 baud, the data rate goes from 80kbit/sec to
113kbit/sec, so gets close to saturating the UART link without loss of
data.
The new raw REPL mode also supports a single ctrl-C to break out of this
flow-control mode, so that a ctrl-C can always get back to a known state.
It's also backwards compatible with the original raw REPL mode, which is
still supported with the same sequence of commands. The new raw REPL
mode is activated by ctrl-E, which gives an error on devices that do not
support the new mode.
Signed-off-by: Damien George <damien@micropython.org>
Travis now limits the amount of free minutes for open-source projects, and
it does not provide enough for this project. So stop using it and instead
use on GitHub Actions.
Signed-off-by: Damien George <damien@micropython.org>
Also known as L2CAP "connection oriented channels". This provides a
socket-like data transfer mechanism for BLE.
Currently only implemented for NimBLE on STM32 / Unix.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Hardware I2C implementations must provide a .init() protocol method if they
want to support reconfiguration. Otherwise the default is that i2c.init()
raises an OSError (currently the case for all ports).
mp_machine_soft_i2c_locals_dict is renamed to mp_machine_i2c_locals_dict to
match the generic SPI bindings.
Fixes issue #6623 (where calling .init() on a HW I2C would crash).
Signed-off-by: Damien George <damien@micropython.org>
This fixes the build for non-STM32WB based boards when the NimBLE submodule
has not been fetched, and also allows STM32WB boards to build with BLE
disabled.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This is needed to moderate concurrent access to the internal flash, as
while an erase/write is in progress execution will stall on the wireless
core due to the bus being locked.
This implements Figure 10 from AN5289 Rev 3.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit switches the STM32WB HCI interface (between the two CPUs) to
require the use of MICROPY_PY_BLUETOOTH_USE_SYNC_EVENTS, and as a
consequence to require NimBLE. IPCC RX IRQs now schedule the NimBLE
handler to run via mp_sched_schedule.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This test currently passes on Unix/PYBD, but fails on WB55 because it lacks
synchronisation of the internal flash.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This changes stm32 from using PENDSV to run NimBLE to use the MicroPython
scheduler instead. This allows Python BLE callbacks to be invoked directly
(and therefore synchronously) rather than via the ringbuffer.
The NimBLE UART HCI and event processing now happens in a scheduled task
every 128ms. When RX IRQ idle events arrive, it will also schedule this
task to improve latency.
There is a similar change for the unix port where the background thread now
queues the scheduled task.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This requires that the event handlers are called from non-interrupt context
(i.e. the MicroPython scheduler).
This will allow the BLE stack (e.g. NimBLE) to run from the scheduler
rather than an IRQ like PENDSV, and therefore be able to invoke Python
callbacks directly/synchronously. This allows writing Python BLE handlers
for events that require immediate response such as _IRQ_READ_REQUEST (which
was previous a hard IRQ) and future events relating to pairing/bonding.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Using a semaphore (the previous approach) will only run the UART, whereas
for startup we need to also run the event queue.
This change makes it run the full scheduler hook.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Instead of having the stack indicate a "start", "data"..., "end", pass
through the data in one callback as an array of chunks of data.
This is because the upcoming non-ringbuffer modbluetooth implementation
cannot buffer the data in the ringbuffer and requires instead a single
callback with all the data, to pass to the Python callback.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Use the same `wait_for_event` in all tests that doesn't hold a reference to
the event data tuple and handles repeat events.
Also fix a few misc reliability issues around timeouts and sequencing.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Devices with RTC backup-batteries have been shown (very rarely) to have
incorrect RTC prescaler values. Such incorrect values mean the RTC counts
fast or slow, and will be wrong forever if the power/backup-battery is
always present.
This commit detects such a state at start up (hard reset) and corrects it
by reconfiguring the RTC prescaler values.
Signed-off-by: Damien George <damien@micropython.org>
And rename SRC_HAL -> HAL_SRC_C and SRC_USBDEV -> USBDEV_SRC_C for
consistency with other source variables.
Follow on from 0fff2e03fe
Signed-off-by: Damien George <damien@micropython.org>
Prior to this change machine.mem32['foo'] (or using any other non-integer
subscript) could result in a fault due to 'foo' being interpreted as an
integer. And when writing code it's hard to tell if the fault is due to a
bad subscript type, or an integer subscript that specifies an invalid
memory address.
The type of the object used in the subscript is now tested to be an
integer by using mp_obj_get_int_truncated instead of
mp_obj_int_get_truncated. The performance hit of this change is minimal,
and machine.memX objects are more for convenience than performance (there
are many other ways to read/write memory in a faster way),
Fixes issue #6588.
The file `$(BUILD)/firmware.bin` was used by the target `deploy-stlink` and
`deploy-openocd` but it was generated indirectly by the target
`firmware.dfu`.
As this file could be used to program boards directly by a Mass Storage
copy, it's better to make it explicitly generated.
Additionally, some target are refactored to remove redundancy and be more
explicit on dependencies.
This gives a substantial speedup of the preprocessing step, i.e. the
generation of qstr.i.last. For example on a clean build, making
qstr.i.last:
21s -> 4s on STM32 (WB55)
8.9 -> 1.8s on Unix (dev).
Done in collaboration with @stinos.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Running the update inside the soft-reset loop will mean that (on boards
like PYBD that use a bootloader) the same reset mode is used each
reset loop, eg factory reset occurs each time.
Signed-off-by: Damien George <damien@micropython.org>
Add working example code to provide a starting point for users with files
that they can just copy, and include the modules in the coverage test to
verify the complete user C module build functionality. The cexample module
uses the code originally found in cmodules.rst, which has been updated to
reflect this and partially rewritten with more complete information.
Support building .cpp files and linking them into the micropython
executable in a way similar to how it is done for .c files. The main
incentive here is to enable user C modules to use C++ files (which are put
in SRC_MOD_CXX by py.mk) since the core itself does not utilize C++.
However, to verify build functionality a unix overage test is added. The
esp32 port already has CXXFLAGS so just add the user modules' flags to it.
For the unix port use a copy of the CFLAGS but strip the ones which are not
usable for C++.
Support C++ code in .cpp files by providing CXX counterparts of the
_USERMOD_ flags we have for C already. This merely enables the Makefile of
user C modules to use variables specific to C++ compilation, it is still up
to each port's main Makefile to also include these in the build.
When SCR_QSTR contains C++ files they should be preprocessed with the same
compiler flags (CXXFLAGS) as they will be compiled with, to make sure code
scanned for QSTR occurrences is effectively the code used in the rest of
the build. The 'split SCR_QSTR in .c and .cpp files and process each with
different flags' logic isn't trivial to express in a Makefile and the
existing principle for deciding which files to preprocess was already
rather complicated, so the actual preprocessing is moved into
makeqstrdefs.py completely.
When process_file() is passed a preprocessed C++ file for instance it won't
find any lines containing .c files and the last_fname variable remains
None, so handle that gracefully.
If a port provides MICROPY_PY_URANDOM_SEED_INIT_FUNC as a source of
randomness then this will be used when urandom.seed() is called without
an argument (or with None as the argument) to seed the pRNG.
Other related changes in this commit:
- mod_urandom___init__ is changed to call seed() without arguments, instead
of explicitly passing in the result of MICROPY_PY_URANDOM_SEED_INIT_FUNC.
- mod_urandom___init__ will only ever seed the pRNG once (before it could
seed it again if imported by, eg, random and then urandom).
- The Yasmarang state is moved to the BSS for builds where the state is
guaranteed to be initialised on import of the (u)random module.
Signed-off-by: Damien George <damien@micropython.org>
The same seed will only occur if the board is the same, the RTC has the
same time (eg freshly powered up) and the first call to this function (eg
via an "import random") is done at exactly the same time since reset.
Signed-off-by: Damien George <damien@micropython.org>
For seeding, the RNG function of the ESP-IDF is used, which is told to be a
true RNG, at least when WiFi or Bluetooth is enabled. Seeding on import is
as per CPython. To obtain a reproducible sequence of pseudo-random numbers
one must explicitly seed with a known value.
Prior to this commit, the ADC calibration code was never executing because
ADVREGEN bit was set making the CR register always non-zero.
This commit changes the logic so that ADC calibration is always run when
the ADC is disabled and an ADC channel is initialised. It also uses the LL
API functions to do the calibration, to make sure it is done correctly on
each MCU variant.
Signed-off-by: Damien George <damien@micropython.org>
When threading is enabled without the GIL then there can be races between
the threads accessing the globals dict. Avoid this issue by making sure
all globals variables are allocated before starting the threads.
Signed-off-by: Damien George <damien@micropython.org>
Newer GCC versions are able to warn about switch cases that fall
through. This is usually a sign of a forgotten break statement, but in
the few cases where a fall through is intended we annotate it with this
macro to avoid the warning.
Like Clang, GCC warns about this file, but only with -Woverride-init
which is enabled by -Wextra. Disable the warnings for this file just
like we do for Clang to make -Wextra happy.
When compiling with -Wextra which includes -Wmissing-field-initializers
GCC will warn that the defval field of mp_arg_val_t is not initialized.
This is just a warning as it is defined to be zero initialized, but since
it is a union it makes sense to be explicit about which member we're
going to use, so add the explicit initializers and get rid of the
warning.
On x86 chars are signed, but we're comparing a char to '0' + unsigned int,
which is promoted to an unsigned int. Let's promote the char to unsigned
before doing the comparison to avoid weird corner cases.
The function scope_find_or_add_id used to take a scope_kind_t enum and
save it in an uint8_t. Saving an enum in a uint8_t is fine, but
everywhere this function is called it is not actually given a
scope_kind_t but an anonymous enum instead. Let's give this enum a name
and use that as the argument type.
This doesn't change the generated code, but is a C type mismatch that
unfortunately doesn't show up unless you enable -Wenum-conversion.
If the device is not connected over USB CDC to a host then all output to
the CDC (eg initial boot messages) is written to the CDC TX buffer with
wrapping, so that the most recent data is retained when the USB CDC is
eventually connected (eg so the REPL banner is displayed upon connection).
This commit fixes a bug in this behaviour, which was likely introduced in
e4fcd216e0, where the initial data in the CDC
TX buffer is repeated multiple times on first connection of the device to
the host.
Signed-off-by: Damien George <damien@micropython.org>
This is a generally useful feature and because it's part of the object
model it cannot be added at runtime by some loadable Python code, so enable
it on the standard unix build.
The last argument of TUD_CDC_DESCRIPTOR() is the endpoint size (or
wMaxPacketSize), not the CDC RX buffer size (which can be larger than the
endpoint size).
Signed-off-by: Damien George <damien@micropython.org>
When installing WS firmware, the very first GET_STATE can take several
seconds to respond (especially with the larger binaries like
BLE_stack_full).
Allows stm.rfcore_sys_hci to take an optional timeout, defaulting to
SYS_ACK_TIMEOUT_MS (which is 250ms).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The flash can sometimes be in an already-unlocked state, and attempting to
unlock it again will cause an immediate reset. So make _Flash.unlock()
check FLASH_CR_LOCK to get the current state.
Also fix some magic numbers for FLASH_CR_LOCK AND FLASH_CR_STRT.
The machine.reset() could be removed because it no longer crashes now that
the flash unlock is fixed.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds a script that can be run on-device to install FUS and WS
binaries from the filesystem. Instructions for use are provided in
the rfcore_firmware.py file.
The commit also removes unneeded functionality from the existing rfcore.py
debug script (and renames it rfcore_debug.py).
The new functions provide FUS/WS status, version and SYS HCI commands:
- stm.rfcore_status()
- stm.rfcore_fw_version(fw_id)
- stm.rfcore_sys_hci(ogf, ocf, cmd)
Changes are:
- Fix missing IRQ handler when SDMMC2 is used instead of SDMMC1 with H7
MCUs.
- Removed outdated H7 series compatibility macros.
- Defined common IRQ handler macro for F4 series.
It requires mp_hal_time_ns() to be provided by a port. This function
allows very accurate absolute timestamps.
Enabled on unix, windows, stm32, esp8266 and esp32.
Signed-off-by: Damien George <damien@micropython.org>
With a warning that this way of constructing software I2C/SPI is
deprecated. The check and warning will be removed in a future release.
This should help existing code to migrate to the new SoftI2C/SoftSPI types.
Signed-off-by: Damien George <damien@micropython.org>
Previous commits removed the ability for one I2C/SPI constructor to
construct both software- or hardware-based peripheral instances. Such
construction is now split to explicit soft and non-soft types.
This commit makes both types available in all ports that previously could
create both software and hardware peripherals: machine.I2C and machine.SPI
construct hardware instances, while machine.SoftI2C and machine.SoftSPI
create software instances.
This is a breaking change for use of software-based I2C and SPI. Code that
constructed I2C/SPI peripherals in the following way will need to be
changed:
machine.I2C(-1, ...) -> machine.SoftI2C(...)
machine.I2C(scl=scl, sda=sda) -> machine.SoftI2C(scl=scl, sda=sda)
machine.SPI(-1, ...) -> machine.SoftSPI(...)
machine.SPI(sck=sck, mosi=mosi, miso=miso)
-> machine.SoftSPI(sck=sck, mosi=mosi, miso=miso)
Code which uses machine.I2C and machine.SPI classes to access hardware
peripherals does not need to change.
Signed-off-by: Damien George <damien@micropython.org>
The SoftSPI constructor is now used soley to create SoftSPI instances, it
can no longer delegate to create a hardware-based SPI instance.
Signed-off-by: Damien George <damien@micropython.org>
The SoftI2C constructor is now used soley to create SoftI2C instances, it
can no longer delegate to create a hardware-based I2C instance.
Signed-off-by: Damien George <damien@micropython.org>
Also rename machine_i2c_type to mp_machine_soft_i2c_type. These changes
make it clear that it's a soft-I2C implementation, and match SoftSPI.
Signed-off-by: Damien George <damien@micropython.org>
Some downstream projects may use tags in their repositories for more than
just designating MicroPython releases. In those cases, the
makeversionhdr.py script would end up using a different tag than intended.
So tell `git describe` to only match tags that look like a MicroPython
version tag, such as `v1.12` or `v2.0`.
Zephyr v2.4.0 added a const qualifier to usages of struct device to
allow storing device driver instances exclusively in flash and thereby
reduce ram footprint.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The use of -S ensures that only the CPython standard library is accessible,
which makes tests run the same regardless of any site-packages that are
installed. It also improves start-up time of CPython, reducing the overall
time spent running the test suite.
tests/basics/containment.py is updated to work around issue with old Python
versions not being able to str-format a dict-keys object, which becomes
apparent when -S is used.
Signed-off-by: Damien George <damien@micropython.org>
A read-only memoryview object is a better representation of the data, which
is owned by the ubluetooth module and may change between calls to the
user's irq callback function.
Signed-off-by: Damien George <damien@micropython.org>
Calling the bytes constructor on a bytes object returns the original bytes
object. This saves allocating a new instance, and matches CPython.
Signed-off-by: Iyassou Shimels <s.iyassou@gmail.com>
Make the instructions more complete by documenting all needed steps for
starting from scratch. Also add a section for MSYS2 since the Travis build
uses it as well and it's a good alternative for Cygwin. Remove the mingw32
reference since it's not readily available anymore in most Linux distros
nor compiles successfully.
Prior to this commit, uos.chdir('/') followed by uos.stat('noexist') would
succeed that stat even though the entry did not exist (some other functions
like listdir would have similar issues). This is because, if the current
directory was the root and the path was relative, mp_vfs_lookup_path would
return success for bad paths.
Signed-off-by: Damien George <damien@micropython.org>
The device info table has a different layout when core 2 is in FUS mode.
In particular it's larger than the 32 bytes used when in WS mode and if the
correct amount of space is not allocated then the end of the table may be
overwritten with other data (eg with FUS version 0.5.3). So update the
structure to fix this.
Also update rfcore.py to disable IRQs (which are enabled by rfcore.c), to
not depend on uctypes, and to not require the asm_thumb emitter.
Signed-off-by: Damien George <damien@micropython.org>
And enable this feature on unix, the coverage variant. The .exp test file
is needed so the test can run on CPython versions prior to "@=" operator
support.
Signed-off-by: Damien George <damien@micropython.org>
For time-based functions that work with absolute time there is the need for
an Epoch, to set the zero-point at which the absolute time starts counting.
Such functions include time.time() and filesystem stat return values. And
different ports may use a different Epoch.
To make it clearer what functions use the Epoch (whatever it may be), and
make the ports more consistent with their use of the Epoch, this commit
renames all Epoch related functions to include the word "epoch" in their
name (and remove references to "2000").
Along with this rename, the following things have changed:
- mp_hal_time_ns() is now specified to return the number of nanoseconds
since the Epoch, rather than since 1970 (but since this is an internal
function it doesn't change anything for the user).
- littlefs timestamps on the esp8266 have been fixed (they were previously
off by 30 years in nanoseconds).
Otherwise, there is no functional change made by this commit.
Signed-off-by: Damien George <damien@micropython.org>
To portably get the Epoch. This is simply aliased to localtime() on ports
that are not timezone aware.
Signed-off-by: Damien George <damien@micropython.org>
This commit removes release-specific builds for the esp8266 and makes the
normal build of the GENERIC board more like the release build. This makes
esp8266 like all the other ports, for which there is no difference between
a daily build and a release build, making things less confusing.
Release builds were previously defined by UART_OS=-1 (disable OS messages)
and using manifest_release.py to include more frozen modules.
The changes in this commit are:
- Remove manifest_release.py.
- Add existing modules from manifest_release.py (except example code)
to the GENERIC board's manifest.py file.
- Change UART_OS default to -1 to disable OS messages by default.
Signed-off-by: Damien George <damien@micropython.org>
PPP support was disabled in 96008ff59a -
marked as "unsupported" due to an early IDF v4 release. With the currently
supported IDF v4.x version - 4c81978a - it appears to be working just fine.
This commit changes the default logging level on all esp32 boards to ERROR.
The esp32 port is now stable enough that it makes sense to remove the info
logs to make the output cleaner, and to match other ports. More verbose
logging can always be reenabled via esp.osdebug().
This also fixes issue #6354, error messages from NimBLE: the problem is
that ble.active(True) will cause the IDF's NimBLE port to reset the
"NimBLE" tag back to the default level (which was INFO prior to this
commit). Even if the user had previously called esp.osdebug(None), because
the IDF is setting the "NimBLE" tag back to the default (INFO), the
messages will continue to be shown.
The one quirk is that if the user does want to see the additional logging,
then they must call esp.osdebug(0, 3) after ble.active(True) to undo the
IDF setting the level back to the default (now ERROR). This means that
it's impossible (via Python/esp.osdebug) to see stack-startup logging,
you'd have to recompile with the default level changed back to INFO.
For the following 3 functions, previously the code relied on whether the
arg was passed at all, to make it optional. Now it allows them to be
explicitly `None` to indicate they are not used:
- gatts_notify(..., [data])
- gattc_discover_services(..., [uuid])
- gattc_discover_characteristics(..., [uuid])
Also ensure that the uuid arguments are actually instances of the uuid
type, and fix handling of the 5th arg in gattc_discover_characteristics().
Support freezing modules via manifest.py for consistency with the other
ports. In essence this comes down to calling makemanifest.py and adding
the resulting .c file to the build. Note the file with preprocessed qstrs
has been renamed to match what makemanifest.py expects and which is also
the name all other ports use.
The msvc compiler doesn't accept zero-sized arrays so let the freezing
process generate compatible C code in case no modules are found and the
involved arrays are all empty. This doesn't affect the functionality in
any way because those arrays only get accessed when mp_frozen_mpy_names
contains names, i.e. when modules are actually found.
Prior to this commit, pow(-2, float('nan')) would return (nan+nanj), or
raise an exception on targets that don't support complex numbers. This is
fixed to return simply nan, as CPython does.
Signed-off-by: Damien George <damien@micropython.org>
The mpconfigport.h file is an internal header and should only ever be
included once by mpconfig.h.
Signed-off-by: Damien George <damien@micropython.org>
MP_BC_CALL_FUNCTION will leave the result on the Python stack, so that
result must be discarded by MP_BC_POP_TOP.
Signed-off-by: Damien George <damien@micropython.org>
This allows prototyping rfcore.c improvements from Python.
This was mostly written by @dpgeorge with small modifications to work after
rfcore_init() by @jimmo.
Before this change there was up to a 128ms delay on incoming payloads from
CPU2 as it was polled by SysTick. Now the RX IRQ immediately schedules the
PendSV.
This is required to allow using WS firmware newer than 1.1.1 concurrently
with USB (e.g. USB VCP). It prevents CPU2 from modifying the CLK48 config
on boot.
Tested on WS=1.8 FUS=1.1.
See AN5289 and https://github.com/micropython/micropython/issues/6316
- Split tables and buffers into SRAM2A/2B.
- Use structs rather than word offsets to access tables.
- Use FLASH_IPCCDBA register value rather than option bytes directly.
This allows `ble.active(1)` to fail correctly if the HCI controller is
unavailable.
It also avoids an infine loop in the NimBLE event handler where NimBLE
doesn't correctly detect that the HCI controller is unavailable and keeps
trying to reset.
Furthermore, it fixes an issue where GATT service registrations were left
allocated, which led to a bad realloc if the stack was activated multiple
times.
MicroPython and NimBLE must be on the same core, for synchronisation of the
BLE ringbuf and the MicroPython scheduler. However, in the current IDF
versions (3.3 and 4.0) there are issues (see e.g. #5489) with running
NimBLE on core 1.
This change - pinning both tasks to core 0 - makes it possible to reliably
run the BLE multitests on esp32 boards.
Generally a controller should either have its own public address hardcoded,
or loaded by the driver (e.g. cywbt43).
However, for a controller that has no public address where you still want a
long-term stable address, this allows you to use a static address generated
by the port. Typically on STM32 this will be an LAA, but a board might
override this.
This commit adds support for using Bluetooth on the unix port via a H4
serial interface (distinct from a USB dongle), with both BTstack and NimBLE
Bluetooth stacks.
Note that MICROPY_PY_BLUETOOTH is now disabled for the coverage variant.
Prior to this commit Bluetooth was anyway not being built on Travis because
libusb was not detected. But now that bluetooth works in H4 mode it will
be built, and will lead to a large decrease in coverage because Bluetooth
tests cannot be run on Travis.
Previously the interaction between the different layers of the Bluetooth
stack was different on each port and each stack. This commit defines
common interfaces between them and implements them for cyw43, btstack,
nimble, stm32, unix.
mp_irq_init() is useful when the IRQ object is allocated by the caller.
The mp_irq_methods_t.init method is not used anywhere so has been removed.
Signed-off-by: Damien George <damien@micropython.org>
This is consistent with the other 'micro' modules and allows implementing
additional features in Python via e.g. micropython-lib's sys.
Note this is a breaking change (not backwards compatible) for ports which
do not enable weak links, as "import sys" must now be replaced with
"import usys".
2020-09-04 00:10:24 +10:00
1395 changed files with 56538 additions and 11025 deletions
``active`` can be set ``True`` if you want to receive scan responses in the results.
When scanning is stopped (either due to the duration finishing or when
explicitly stopped), the ``_IRQ_SCAN_DONE`` event will be raised.
Central Role
------------
A central device can connect to peripherals that it has discovered using the observer role (see :meth:`gap_scan<BLE.gap_scan>`) or with a known address.
For all ports, DMA runs continuously in the background and allows user applications to perform other operations while
sample data is transfered between the internal buffer and the I2S peripheral unit.
Increasing the size of the internal buffer has the potential to increase the time that user applications can perform non-I2S operations
before underflow (e.g. ``write`` method) or overflow (e.g. ``readinto`` method).
Methods
-------
..method:: I2S.init(sck, ...)
see Constructor for argument descriptions
..method:: I2S.deinit()
Deinitialize the I2S bus
..method:: I2S.readinto(buf)
Read audio samples into the buffer specified by ``buf``. ``buf`` must support the buffer protocol, such as bytearray or array.
"buf" byte ordering is little-endian. For Stereo format, left channel sample precedes right channel sample. For Mono format,
the left channel sample data is used.
Returns number of bytes read
..method:: I2S.write(buf)
Write audio samples contained in ``buf``. ``buf`` must support the buffer protocol, such as bytearray or array.
"buf" byte ordering is little-endian. For Stereo format, left channel sample precedes right channel sample. For Mono format,
the sample data is written to both the right and left channels.
Returns number of bytes written
..method:: I2S.irq(handler)
Set a callback. ``handler`` is called when ``buf`` is emptied (``write`` method) or becomes full (``readinto`` method).
Setting a callback changes the ``write`` and ``readinto`` methods to non-blocking operation.
``handler`` is called in the context of the MicroPython scheduler.
..staticmethod:: I2S.shift(buf, bits, shift)
bitwise shift of all samples contained in ``buf``. ``bits`` specifies sample size in bits. ``shift`` specifies the number of bits to shift each sample.
Positive for left shift, negative for right shift.
Typically used for volume control. Each bit shift changes sample volume by 6dB.
Takes a `stream`*sock* (usually socket.socket instance of ``SOCK_STREAM`` type),
and returns an instance of ssl.SSLSocket, which wraps the underlying stream in
an SSL context. Returned object has the usual `stream` interface methods like
``read()``, ``write()``, etc.
A server-side SSL socket should be created from a normal socket returned from
:meth:`~socket.socket.accept()` on a non-SSL listening server socket.
-*do_handshake* determines whether the handshake is done as part of the ``wrap_socket``
or whether it is deferred to be done as part of the initial reads or writes
(there is no ``do_handshake`` method as in CPython).
For blocking sockets doing the handshake immediately is standard. For non-blocking
sockets (i.e. when the *sock* passed into ``wrap_socket`` is in non-blocking mode)
the handshake should generally be deferred because otherwise ``wrap_socket`` blocks
until it completes. Note that in AXTLS the handshake can be deferred until the first
read or write but it then blocks until completion.
Depending on the underlying module implementation in a particular
:term:`MicroPython port`, some or all keyword arguments above may be not supported.
..warning::
Some implementations of ``ssl`` module do NOT validate server certificates,
which makes an SSL connection established prone to man-in-the-middle attacks.
CPython's ``wrap_socket`` returns an ``SSLSocket`` object which has methods typical
for sockets, such as ``send``, ``recv``, etc. MicroPython's ``wrap_socket``
returns an object more similar to CPython's ``SSLObject`` which does not have
these socket methods.
Exceptions
----------
..data:: ssl.SSLError
This exception does NOT exist. Instead its base class, OSError, is used.
Constants
---------
..data:: ssl.CERT_NONE
ssl.CERT_OPTIONAL
ssl.CERT_REQUIRED
Supported values for *cert_reqs* parameter.
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
