4424 Commits

Author	SHA1	Message	Date
iabdalkader	94343e20e5	stm32/boards/STM32F429DISC: Fix SDRAM configuration. ... Define SDRAM frequency and refresh cycles. This was missed in commit 17808e7b74. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-11 12:17:40 +11:00
Angus Gratton	d4d1d4798c	esp32: Simplify thread cleanup. ... Now we only support the case of !CONFIG_FREERTOS_ENABLE_STATIC_TASK_CLEAN_UP, can simplify the cleanup code. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-12-10 23:21:46 +11:00
Angus Gratton	d90aff5e13	esp32: Remove IDF-version-specific sdkconfig. ... This reverts commit 27279e69b4 (plus removes some additional references to the SDKCONFIG_IDF_VERSION_SPECIFIC CMake variable.) Relevant sdkconfig options are added into sdkconfig.base now that IDF >=5.2.0 is required. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-12-10 23:21:46 +11:00
Angus Gratton	6e5d8d0093	esp32: Drop support for ESP-IDF below V5.2.0. ... Specifically, remove all conditional compilation for these earlier versions and change the idf_component.yml specifiers to require >=5.2.0. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-12-10 23:21:46 +11:00
Alessandro Gatti	82e382a399	esp32/mpconfigport: Use the appropriate wait-for-interrupt opcode. ... When threading is disabled, the pending events handling code would wait for an incoming interrupt once there's no more work to do. This bit of code was Xtensa-specific and wouldn't compile on a RISC-V based MCU. This commit provides the RISC-V equivalent to that part of the code, allowing to make threadless MicroPython builds on RISC-V based MCUs. Signed-off-by: Alessandro Gatti <a.gatti@frob.it>	2024-12-10 21:57:40 +11:00
Andrew Leech	9441ce6e3c	esp32: Use capability defines to configure features. ... This updates esp32 code where appropriate to replace ifdef's based on a list of specific chips with a feature SOC_* definition. This should simplify adding new esp32-* chips in future, deferring chip feature support to the IDF. Signed-off-by: Andrew Leech <andrew@alelec.net>	2024-12-10 21:47:05 +11:00
Alessandro Gatti	e8c3f31ba2	mimxrt/machine_rtc: Deprecate RTC.cancel in MicroPython v2. ... The current documentation for the `machine.RTC` class contains information about the `RTC.cancel` method for cancelling pending alarms. However only two ports (cc3200 and mimxrt) implement this functionality but under a different name: `RTC.alarm_cancel`. The mimxrt port also implements `RTC.cancel` but it is aliased to `RTC.alarm_cancel` anyway. To maintain naming consistency, this commit updates the documentation to officially define `RTC.alarm_cancel` as the method to call to cancel pending alarms and deprecates mimxrt's `RTC.cancel` implementation. `RTC.cancel` in the mimxrt port is thus scheduled for removal in MicroPython v2. Signed-off-by: Alessandro Gatti <a.gatti@frob.it>	2024-12-10 12:16:03 +11:00
Angus Gratton	31a1e2b96d	rp2: Pass V=1 or BUILD_VERBOSE to rp2 build. ... Similar to esp32. Previously rp2 could build verbose by passing VERBOSE=1, which is picked up by Makefiles generated from CMake. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-12-10 11:28:38 +11:00
Angus Gratton	160a4812cd	esp32: Pass V=1 or BUILD_VERBOSE through to idf.py when building. ... Allows verbose build to work the same on esp32 port as other ports. To minimise copy/paste, split the BUILD_VERBOSE section of mkenv.mk out to its own verbose.mk and include this in the port Makefile. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-12-10 11:28:38 +11:00
Daniël van de Giessen	5fb846df67	esp32: Fix machine_touchpad compiling on IDFv5.3. ... Signed-off-by: Damien George <damien@micropython.org>	2024-12-10 11:20:15 +11:00
Andrew Leech	5564f3042c	esp32: Add basic espressif IDF v5.3 compatibility. ... Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au> Signed-off-by: Damien George <damien@micropython.org>	2024-12-10 11:20:00 +11:00
Angus Gratton	b20687d0e7	esp32: Fix link failure due to link library order. ... When a wrapped symbol is provided in its own file, it's possible for the linker to skip that file entirely and not return to it depending on the order of libraries passed on the linker command line. This is because these wrapped symbols create linker cycles (libmain_espXX depends on liblwip but liblwip now also depends on libmain for the wrapped functions in lwip_patch.c, for example.) Linker failure for symbols in lwip_patch.c was reproducible if mDNS was disabled in the board configuration. This commit adds an explicit undefined symbol for each file, to ensure the linker will add the wrapped objects on its first pass. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-12-10 11:11:31 +11:00
iabdalkader	2bee8e1b8c	mimxrt/mpconfigport: Update FATFS config to align with other ports. ... Make this port use the same FATFS config as stm32, rp2, renesas-ra. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 11:05:05 +11:00
iabdalkader	a2cdf9a95f	renesas-ra/mpconfigport: Switch FATFS LFN to type 2. ... LFN type 2 uses the stack to allocate the internal working buffer for LFN, which is thread-safe and saves about 512 bytes of BSS memory (at the expense of needing that much memory on the stack). Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 11:04:59 +11:00
iabdalkader	309aa26811	rp2/mpconfigport: Switch FATFS LFN to type 2. ... LFN type 2 uses the stack to allocate the internal working buffer for LFN, which is thread-safe and saves about 512 bytes of BSS memory (at the expense of needing that much memory on the stack). Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 11:04:49 +11:00
iabdalkader	fd01cdd203	stm32/mpconfigport: Switch FATFS LFN to type 2. ... LFN type 2 uses the stack to allocate the internal working buffer for LFN, which is thread-safe and saves about 512 bytes of BSS memory (at the expense of needing that much memory on the stack). Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 11:02:52 +11:00
iabdalkader	89191b00ea	stm32/main: Deinitialize SPI and I2C on soft-reset. ... Following UART, CAN, Timer, etc. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:54:16 +11:00
iabdalkader	405aa69887	stm32/pyb_i2c: Add pyb_i2c_deinit_all function. ... I2C objects can remain active after a soft-reboot because they are statically allocated and lack a finalizer to collect and deinitialize them. This commit adds a `pyb_i2c_deinit_all()` function for I2C, similar to other peripherals such as UART, DAC, etc. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:53:47 +11:00
iabdalkader	d42e39d87d	stm32/spi: Add spi_deinit_all function. ... SPI objects can remain active after a soft-reboot because they are statically allocated and lack a finalizer to collect and deinitialize them. This commit adds a `spi_deinit_all()` functions for SPI, similar to other peripherals such as UART, DAC, etc. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:53:24 +11:00
iabdalkader	17808e7b74	stm32/sdram: Make SDRAM refresh count configurable by a board. ... Refresh count calculations were using a hard-coded SDRAM frequency and refresh cycles, so change them to values that can be set by a board. And set these options to their existing values on STM32F769DISC and STM32F7DISC boards. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:49:50 +11:00
iabdalkader	47d9988df2	stm32/boards: Rename SDRAM frequency config option to make units clear. ... Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:49:29 +11:00
iabdalkader	46ca78e23f	stm32/boards: Update Arduino board configs for SPI reset and bootloader. ... Update ARDUINO_GIGA, ARDUINO_OPTA, ARDUINO_NICLA_VISION and ARDUINO_PORTENTA_H7 to: - Enable SPI flash soft-reset. - Disable enter bootloader via reset. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:44:33 +11:00
iabdalkader	d5d366beef	nrf/boards/ARDUINO_NANO_33_BLE_SENSE: Update LED and timer config. ... Changes: - Enable hardware timer. - Define LED pins. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:37:02 +11:00
iabdalkader	67b4e6236b	mimxrt: Switch to shared TinyUSB descriptor. ... This removes duplicated TinyUSB configuration and port-specific code. Tested on RT1062, CDC+MSC still working. @robert-hh tested CDC with 1011, 1015, 1020 and 1176. Signed-off-by: iabdalkader <i.abdalkader@gmail.com>	2024-12-10 10:29:21 +11:00
Damien George	d3d2976586	qemu/Makefile: Include unittest in firmware. ... So that this port can run unittest-based tests. Signed-off-by: Damien George <damien@micropython.org>	2024-12-06 13:48:07 +11:00
Damien George	42f37e951b	esp8266/mpconfigport: Enable function attributes. ... This allows `unittest` to work on esp8266 boards. Signed-off-by: Damien George <damien@micropython.org>	2024-12-06 13:48:07 +11:00
chuangjinglu	2e796d6c3e	docs,ports: Fix some comments and error messages with doubled-up words. ... Signed-off-by: chuangjinglu <chuangjinglu@outlook.com>	2024-11-30 13:08:33 +11:00
Angus Gratton	beabef5aac	esp32: Add missing network.STAT_CONNECT_FAIL constant. ... The esp32 port had network.STAT_ASSOC_FAIL for the same purpose, but this is undocumented and different to all other ports. That constant is now deprecated. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-11-30 12:36:03 +11:00
robert-hh	da692d01ac	nrf/drivers/ticker: Reset slow ticker callback count on soft reboot. ... The micro:bit board (and probably other boards using the music or display module) locked up on soft reboot. Reason was a buffer overflow caused by an index counter, which was not reset on soft_reboot. That's fixed in this commit. Tested with a micro:bit board, performing a series of soft reboots. Signed-off-by: robert-hh <robert@hammelrath.com>	2024-11-28 23:02:46 +11:00
Angus Gratton	66e699e8a5	esp32: Fix machine.TouchPad startup on ESP32-S2 and S3. ... Closes #13178. TouchPad confirmed working on both chips, and fixes the the ESP32-S3 reading constant max value. Was unable to reproduce the bug on ESP32-S2 but this may be due to my test setup, and it still works with the fix. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-11-28 15:45:39 +11:00
Angus Gratton	ed3c75a3af	esp32: Use hardware version for touchpad macro defines. ... ESP32 has hardware V1 and S2/S3 has V2, and future chips may have different versions. This should still compile to the same binary before and after. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-11-28 15:45:39 +11:00
Angus Gratton	951a10e707	esp32: Fix setting WLAN channel in AP mode. ... - Previously the call to esp_wifi_set_channel() would be immediately overridden by calling esp_wifi_config(...) with the previous channel set. - AP interface doesn't seem to need more than esp_wifi_config(...) to work. It will automatically configure 40MHz bandwidth and place the secondary channel using similar logic to what was being explicitly calculated here. - However, calling esp_wifi_set_channel() on the STA interface is necessary if using this interface with ESP-NOW (without connecting to an AP). So the esp_wifi_set_channel() call is kept in for this purpose. Without this, tests/multi_espnow/70_channel.py fails. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-11-28 15:39:06 +11:00
robert-hh	cbffe61f96	samd/mboot/README.md: Add information about the bootloader source. ... Includes the LICENSE file of the source and the specific board files for the Xplained Pro board. Signed-off-by: robert-hh <robert@hammelrath.com>	2024-11-18 18:31:16 +01:00
robert-hh	ceae0e1494	samd/samd_flash: Make flash read/write methods access self parameters. ... Use `self` (the first argument) instead of the global `samd_flash_obj` when accessing the `flash_base` parameter. This allows there to be multiple flash objects for various types of filesystem. Signed-off-by: robert-hh <robert@hammelrath.com>	2024-11-18 23:54:42 +11:00
robert-hh	4a159d16fe	samd/boards/SAMD21_XPLAINED_PRO: Use the SPI flash for the file system. ... The initial settings did not support it. The change required to add a dedicated handling of the Adesto 1MByte flash of the XPLAINED PRO board, which does not support the sfdp feature. Fixes the ID check of the Adesto/Renesas 1MByte flash. Signed-off-by: robert-hh <robert@hammelrath.com>	2024-11-18 23:51:02 +11:00
robert-hh	85de67f55d	samd/mboot: Provide a UF2 bootloader for SAMD21 Xplained Pro. ... A bootloader labelled for the SAMD21 XPLAINED PRO board. The only difference to a generic bootloader are the names and ID of the USB port and the label of the drive that is opened. Signed-off-by: robert-hh <robert@hammelrath.com>	2024-11-18 23:50:20 +11:00
robert-hh	4d36ecf8a8	samd/boards/SAMD21_XPLAINED_PRO: Add specific deploy instructions. ... Add instructions to install a bootloader to the board. The SAMD21 XPLAINED PRO board is shipped without a bootloader, which therefore has to be installed once before it can be used with MicroPython. Signed-off-by: robert-hh <robert@hammelrath.com>	2024-11-18 23:49:39 +11:00
robert-hh	5a70850b30	samd/machine_uart: Add full support for 9-bit data. ... Prior to this commit, 9-bit UART data could be specified in the constructor and was transmitted, but the 9th bit was set to 0 when sending, and ignored when receiving. This commit completes 9-bit support in that the 9th bit is taken from the data. 9-bit data has to be provided with `uart.write()` and and read with `uart.read()` as two bytes for each transmitted item, low order byte first. The data length supplied with `uart.write()` and requested by `uart.read()` has to be even, which is checked. The size of the UART buffers will be transparently doubled to cater for 9-bit data. Signed-off-by: robert-hh <robert@hammelrath.com>	2024-11-18 23:05:46 +11:00
robert-hh	e2532e0f72	mimxrt/machine_pwm: Fix a few inconsistencies with PWM output. ... Changes in this commit: - When setting PWM parameters of a FLEXPWM AB channel twice within a PWM cycle, the second setting was ignored. Now the second setting persists. - With `duty_u16(0)` a FLEXPWM X channel was set to high impedance. Now it is set to low impedance with value 0 for `invert=False`, and 1 for `invert=True`. - The align parameter requires a duty rate and frequency to be set. Align will now be ignored if freq or duty are missing. Signed-off-by: robert-hh <robert@hammelrath.com>	2024-11-18 16:11:13 +11:00
robert-hh	898407defb	ports: Make PWM duty_u16 have an upper value of 65535 across all ports. ... The following ports used 65536 as the upper value (100% duty cycle) and are changed in this commit to use 65535: esp8266, mimxrt, nrf, samd. Tested that output is high at `duty_u16(65535)` and low at `duty_u16(0)`. Also verified that at `duty_u16(32768)` the high and low pulse have the same length. Partially reverts #10850, commits 9c7ad68165 and 2ac643c15b. Signed-off-by: robert-hh <robert@hammelrath.com>	2024-11-18 16:05:56 +11:00
Damien George	611d8f9ce8	esp32/modsocket: Fix getaddrinfo hints to set AI_CANONNAME. ... Because the `ai_canonname` field is subsequently used. ESP32_GENERIC_S3 (at least) crashes with IDF 5.2.3 without this set. Signed-off-by: Damien George <damien@micropython.org>	2024-11-13 13:35:37 +11:00
Daniël van de Giessen	77406b4240	extmod/network_ppp: Allow stream=None to suspend PPP. ... This allows the stream to be set to `None`, which essentially stops all PPP communication without disconnecting the session. This allows replacing the stream on-the-fly to suspend it, for example to send AT commands to a modem without completely disconnecting and re-establishing the PPP connection: uart = ppp.config('stream') ppp.config(stream=None) uart.write(b'+++') # do some AT commands uart.write(b'ATO\r\n') ppp.config(stream=uart) Any attempted communication by PPP while the stream is not connected will register as simple packet loss to the LwIP stack because we return 0 for any write calls, and protocols like TCP will then automatically handle retrying. Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>	2024-11-13 13:11:32 +11:00
Daniël van de Giessen	161e2bd37d	extmod/network_ppp: Add stream config parameter. ... This makes the stream that the PPP object wraps, which is normally only set once via the constructor, accessible and configurable via the `ppp.config()` method. Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>	2024-11-13 13:10:58 +11:00
Angus Gratton	f5b81bee61	esp8266: Use the recommended network.WLAN.IF_[AP|STA] constants. ... Removes the deprecated network.[AP|STA]_IF form from the esp8266 port This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-11-08 12:03:48 +11:00
Angus Gratton	285e1d0b80	esp32: Use the recommended network.WLAN.IF_[AP|STA] constants. ... Removes the deprecated network.[AP|STA]_IF form from the esp32 port This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-11-08 10:11:03 +11:00
Angus Gratton	df6b40a87f	esp32: Workaround native code execution crash on ESP32-S2. ... Seemingly ESP-IDF incorrectly marks RTC FAST memory region as MALLOC_CAP_EXEC on ESP32-S2 when it isn't. This memory is the lowest priority, so it only is returned if D/IRAM is exhausted. Apply this workaround to treat the allocation as failed if it gives us non-executable RAM back, rather than crashing. This work was funded through GitHub Sponsors. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-11-06 16:08:23 +11:00
Angus Gratton	594670e446	esp32/machine_pwm: Restore PWM support for ESP-IDF v5.0.x and v5.1.x. ... The cleanup in 548babf8 relies on some functions not available in older ESP-IDF. Temporarily restore them, until we drop support for ESP-IDF <5.2. PWM functionality should end up the same regardless of ESP-IDF version, and also no different from MicroPython V1.23. Signed-off-by: Angus Gratton <angus@redyak.com.au>	2024-11-05 17:19:58 +11:00
Damien George	275b3afae7	esp32/network_wlan: Add missing WLAN security constants. ... These were added to the `network` module but not the `network.WLAN` class, which is the new home for such constants. Also: - Mark the WLAN constants in the `network` module as deprecated, to be removed in MicroPython 2.0. - Move the static assert to the WLAN source code, to be close to where it relates to. Signed-off-by: Damien George <damien@micropython.org>	2024-11-05 11:34:35 +11:00
Damien George	8978102f35	tests/run-tests.py: Change --target/--device options to --test-instance. ... Previously to this commit, running the test suite on a bare-metal board required specifying the target (really platform) and device, eg: $ ./run-tests.py --target pyboard --device /dev/ttyACM1 That's quite a lot to type, and you also need to know what the target platform is, when a lot of the time you either don't care or it doesn't matter. This commit makes it easier to run the tests by replacing both of these options with a single `--test-instance` (`-t` for short) option. That option specifies the executable/port/device to test. Then the target platform is automatically detected. The `--test-instance` can be passed: - "unix" (the default) to use the unix version of MicroPython - "webassembly" to test the webassembly port - anything else is considered a port/device to pass to Pyboard There are also some shortcuts to specify a port/device, following `mpremote`: - a<n> is short for /dev/ttyACM<n> - u<n> is short for /dev/ttyUSB<n> - c<n> is short for COM<n> For example: $ ./run-tests.py -t a1 Note that the default test instance is "unix" and so this commit does not change the standard way to run tests on the unix port, by just doing `./run-tests.py`. As part of this change, the platform (and it's native architecture if it supports importing native .mpy files) is show at the start of the test run. Signed-off-by: Damien George <damien@micropython.org>	2024-11-04 12:47:47 +11:00
Alessandro Gatti	d34b15ac6f	pic16bit: Make it build with recent XC16 versions. ... The PIC16 port didn't catch up with the other ports, so it required a bit of work to make it build with the latest version of XC16. Signed-off-by: Alessandro Gatti <a.gatti@frob.it>	2024-10-30 17:21:30 +11:00